|
Item
|
Specification
|
|
Brake fluid type
|
European (L.H.D. U.K.) specs.:
SAE J1703, FMVSS 116 DOT-3 or DOT-4
Australian, General (L.H.D. R.H.D.) specs.:
SAE J1703, FMVSS 116 DOT-3
|
|
Brake pedal height (reference value)
|
L.H.D.: 187 mm {7.36 in}
R.H.D.: 172 mm {6.77 in}
|
|
Brake pedal play
|
0-3 mm {0-0.1 in}
|
|
Brake pedal-to-floor clearance (Brake pedal when depressed at 588 N {60 kgf, 132 lbf})
|
68 mm {2.7 in} or more
|
|
Power brake unit fluid pressure when pedal depressed at 200 N {20 kgf, 44 lbf}
|
At 0 kPa {0 mmHg, 0 inHg}: 590 kPa {6.02 kgf/cm2, 85.6 psi}
|
|
Power brake unit fluid pressure when pedal depressed at 200 N {20 kgf, 44 lbf}
|
At 66.7 kPa {500 mmHg, 19.7 inHg}:
8,780 kPa {89.53 kgf/cm2, 1,273 psi}
|
|
Proportioning valve fluid pressure
(without ABS (ABS/TCS) or DSC)
|
Rear brake fluid pressure when front brake fluid pressure
at 2,450 kPa {25 kgf/cm2, 355 psi}:
2,450 kPa {25 kgf/cm2, 355 psi} ± 200 kPa {2 kgf/cm2, 29 psi}
Rear brake fluid pressure when front brake fluid pressure
at 5,880 kPa {60 kgf/cm2, 853 psi}:
3,480 kPa {35.5 kgf/cm2, 505 psi} ± 300 kPa {3 kgf/cm2, 44 psi}
|
|
Front disc plate runout limit
|
0.05 mm {0.002 in}
|
|
Minimum front disc plate thickness (European (L.H.D. U.K.) specs.)
|
L8 (4SDN, 5HB): 22 mm {0.87 in}
L8 (WGN), LF, L3, L3 Turbo, MZR-CD (RF Turbo): 23 mm {0.91 in}
|
|
Minimum front disc plate thickness (Australian, General (L.H.D. R.H.D.) specs.)
|
4SD (except L3 Turbo), 5HB, WGN (except Australian specs.):
22 mm {0.87 in}
4SD (L3 Turbo), WGN (Australian specs.): 23 mm {0.91 in}
|
|
Minimum front disc plate thickness after machining using a brake lathe on-vehicle (European (L.H.D. U.K.) specs.)
|
L8 (4SDN, 5HB): 22.8 mm {0.90 in}
L8 (WGN), LF, L3, L3 Turbo, MZR-CD (RF Turbo): 23.8 mm {0.94 in}
|
|
Minimum front disc plate thickness after machining using a brake lathe on-vehicle (Australian, General (L.H.D. R.H.D.) specs.)
|
4SD (except L3 Turbo), 5HB, WGN (except Australian specs.):
22.8 mm {0.90 in}
4SD (L3 Turbo), WGN (Australian specs.): 23.8 mm {0.94 in}
|
|
Minimum front disc pad thickness (European (L.H.D. U.K.) specs.)
|
L8 (4SDN, 5HB): 2.0 mm {0.079 in} min.
L8 (WGN), LF, L3, L3 Turbo, MZR-CD (RF Turbo):
1.5 mm {0.059 in} min.
|
|
Minimum front disc pad thickness (Australian, General (L.H.D. R.H.D.) specs.)
|
4SD (except L3 Turbo), 5HB, WGN (except Australian specs.):
2.0 mm {0.079 in} min.
4SD (L3 Turbo), WGN (Australian specs.): 1.5 mm {0.059 in} min.
|
|
Rear disc plate runout limit
|
0.05 mm {0.002 in}
|
|
Minimum rear disc plate thickness
|
Except 18 inch wheel: 8 mm {0.31 in}
18 inch wheel: 9 mm {0.35 in}
|
|
Minimum rear disc plate thickness after machining using a brake lathe on-vehicle
|
Except 18 inch wheel: 8.8 mm {0.35 in}
18 inch wheel: 9.8 mm {0.39 in}
|
|
Minimum rear disc pad thickness
|
2.0 mm {0.079 in} min.
|
|
Parking brake lever stroke when pulled at 98 N {10 kgf, 22 lbf}
|
2-5 notches
|