DTC P0733 (GENERAL (L.H.D.) SPECS. SPORT AT) [FN4A-EL]

id0502a18021a7

DTC P0733

Gear 3 incorrect (Incorrect Gear Ratio Detected)

DETECTION CONDITION

• TCM monitors revolution ratio of forward clutch drum revolution to differential gear case revolution when the following monitoring conditions are met. If revolution ratio is below 0.863 or above 1.249, TCM determines that there is malfunction.
Monitoring condition:
- ATF temperature 20 °C {68 °F} or above.
- Driving in 3 GR in D range.
- Engine runs.
- Turbine speed within 225-4,988 rpm.
- Differential gear case (output) revolution speed 35 rpm or above.
- Any of the following are not generated: DTC P0706, P0707, P0708, P0712, P0713, P0715, P0720, P0751, P0752, P0753, P0756, P0757, P0758, P0761, P0762, P0763, P0766, P0767, P0768, P0771, P0772, P0773.
Diagnostic support note:
• This is a continuous monitor (CCM).
• MIL does not illuminate.
• AT warning light illuminates if TCM detects the above malfunction condition during first drive cycle.
• FREEZE FRAME DATA is not available.
• Pending code is not available.
• DTC stored in the TCM memory.

POSSIBLE CAUSE

• ATF level low.
• Deteriorated ATF.
• Shift solenoids A or C stuck.
• Pressure control solenoid stuck.
• Line pressure low.
3-4 clutch slipping.
• Forward clutch slipping.
• Control valve stuck (Bypass, TCC or 3-4 shift valve).
• Oil pump.
• TCM malfunction.

Diagnostic procedure

STEP

INSPECTION

ACTION

1

VERIFY RELATED REPAIR INFORMATION AVAILABILITY

• Check for related Service Bulletins availability.
• Is any related repair information available?
Yes
Perform repair or diagnosis according to available repair information.
No
Go to next step.
2

CHECK ATF CONDITION

• Check ATF condition.
• Is it okay?
Yes
Go to next step.
No
Replace transaxle, then go to Step 8.
3

CHECK ATF LEVEL

• Start engine.
• Warm up ATX.
• Is ATF level within specification?
Yes
Go to next step.
No
Adjust ATF level, then go to Step 8.
4

INSPECTION SHIFT SOLENOID VALVE A AND C FOR CLICK SOUND

• Perform inspection of operation.
• Verify the click sound of shift solenoid A and C when applying B+ to each transaxle connector terminal.
• Was click heard from solenoids?
Yes
Go to next step.
No
Replace solenoid where click sound could not be heard, then go to Step 8.
5

INSPECT LINE PRESSURE

• Start engine.
• Measure line pressures.

Specification

D, M (1GR, 2GR) range

Idle: 330-470 kPa {3.4-4.8 kgf/cm2,

48-68 psi}

Stall: 1,160-1,320 kPa {11.8-13.5 kgf/cm2, 168-191 psi}

R position

Idle: 490-710 kPa {5.0-7.2 kgf/cm2,

71-102 psi}

Stall: 1,640-1,970 kPa {16.8-20.0 kgf/cm2, 238-285 psi}

• Is line pressure within specification?
Yes
Go to next step.
No
All ranges: Replace oil pump, then go to Step 8.
Any ranges: Replace control valve body, then go to Step 8.
6

INSPECT STALL SPEED

• Measure stall speed in D range.

Specification

2,000-2,600 rpm

• Is stall speed within specification?
Yes
Go to next step.
No
Replace automatic transaxle, then go to Step 8.
7

INSPECT FREQUENCY OF INPUT/TURBINE SPEED SENSOR WHEN DRIVING VEHICLE

• Turn ignition key to OFF.
• Connect WDS or equivalent.
• Start engine.
• Measure frequency of input/turbine speed sensor while driving vehicle under the following conditions:
- Vehicle speed (VSS PID): 60 km/h {37 mph}
- Drive in D range, 3rd gear
- Throttle opening angle (TP PID): about 25%
• Was frequency of input/turbine speed sensor at approx. 1,200 Hz?
Yes
Go to next step.
No
Replace control valve body, then go to next step.
8

VERIFY REPAIR OF DTC P0732

• Make sure to reconnect all disconnected connectors.
• Clear DTC using WDS or equivalent.
• Start engine.
• Warm up transaxle.
• Drive vehicle under the following conditions for more than 2 seconds.
- ATF temperature: 20 °C {68 °F} or above
- Drive in D range, 3rd gear
- Vehicle speed (VSS PID): 4 km/h {3 mph} or above
• Are any DTCs present?
Yes
Replace TCM, then go to next step.
No
Go to next step.
9

VERIFY AFTER REPAIR PROCEDURE

• Perform "After Repair Procedure".
• Are any DTCs present?
Yes
Go to applicable DTC inspection.
No
Troubleshooting completed.