THEFT-DETERRENT SYSTEM [THEFT-DETERRENT SYSTEM]

id0903l1112700

Description

• Theft-deterrent siren or theft-deterrent horn sounded.

Possible cause

• Rear body control module (RBCM) malfunction

• Customer's mis-operation or misunderstanding

• Theft-deterrent siren malfunction

• Theft-deterrent horn malfunction

• Intruder sensor malfunction

• Wiring harness malfunction

• Malfunction in switch which triggers system

Diagnostic Procedure

Step

Inspection

Action

1

VERIFY DTCs

•  Perform the DTC inspection for the rear body control module (RBCM) using the M-MDS.
(See DTC TABLE [REAR BODY CONTROL MODULE (RBCM)].)

•  Are any DTCs displayed?

Yes

Go to the applicable DTC inspection. (See DTC TABLE [REAR BODY CONTROL MODULE (RBCM)].)

No

Go to the next step.

2

VERIFY OPERATION RECORD

•  Has the operation record been stored?
(See THEFT-DETERRENT SYSTEM OPERATION RECORD.)

Yes

Go to the next step.

No

Diagnosis completed (theft-deterrent system does not operate).

3

VERIFY CONDITION DURING THEFT-DETERRENT SYSTEM OPERATION

•  Is the condition during theft-deterrent operation "Alarm" or "Arming" ?

Yes

Go to the next step.

No

Inspect the rear body control module (RBCM). If there is any malfunction, replace it. (See REAR BODY CONTROL MODULE (RBCM) INSPECTION.)

4

INSPECT THEFT-DETERRENT SIREN

•  Inspect the theft-deterrent siren.
(See THEFT-DETERRENT SIREN INSPECTION.)

•  Is the theft-deterrent siren normal?

Yes

Go to the next step.

No

Replace the theft-deterrent siren, then go to the next step.

(See THEFT-DETERRENT SIREN REMOVAL/INSTALLATION.)

5

INSPECT THEFT-DETERRENT HORN

•  Inspect the theft-deterrent horn.
(See THEFT-DETERRENT HORN INSPECTION.)

•  Is the theft-deterrent horn normal?

Yes

Go to the next step.

No

Replace the intruder sensor, then go to the next step.

(See THEFT-DETERRENT HORN REMOVAL/INSTALLATION.)

6

INSPECT INTRUDER SENSOR

•  Inspect the intruder sensor.
(See INTRUDER SENSOR INSPECTION.)

•  Is the intruder sensor normal?

Yes

Go to the next step.

No

Replace the theft-deterrent horn, then go to the next step.

(See INTRUDER SENSOR REMOVAL/INSTALLATION.)

7

DETERMINE IF MALFUNCTION CAUSE IS SYSTEM

•  Verify what triggered the theft-deterrent system according to the trigger record, and inspect the switch which triggered the system and the related wiring harness.

•  Is the switch or related wiring harness normal?

Yes

System is normal (explain to the customer that the cause is customer's mis-operation).

No

Replace the malfunctioning part.

Step	Inspection		Action
1	VERIFY DTCs • Perform the DTC inspection for the rear body control module (RBCM) using the M-MDS. (See DTC TABLE [REAR BODY CONTROL MODULE (RBCM)].) • Are any DTCs displayed?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [REAR BODY CONTROL MODULE (RBCM)].)
1		No	Go to the next step.
2	VERIFY OPERATION RECORD • Has the operation record been stored? (See THEFT-DETERRENT SYSTEM OPERATION RECORD.)	Yes	Go to the next step.
2		No	Diagnosis completed (theft-deterrent system does not operate).
3	VERIFY CONDITION DURING THEFT-DETERRENT SYSTEM OPERATION • Is the condition during theft-deterrent operation "Alarm" or "Arming" ?	Yes	Go to the next step.
3		No	Inspect the rear body control module (RBCM). If there is any malfunction, replace it. (See REAR BODY CONTROL MODULE (RBCM) INSPECTION.)
4	INSPECT THEFT-DETERRENT SIREN • Inspect the theft-deterrent siren. (See THEFT-DETERRENT SIREN INSPECTION.) • Is the theft-deterrent siren normal?	Yes	Go to the next step.
4		No	Replace the theft-deterrent siren, then go to the next step. (See THEFT-DETERRENT SIREN REMOVAL/INSTALLATION.)
5	INSPECT THEFT-DETERRENT HORN • Inspect the theft-deterrent horn. (See THEFT-DETERRENT HORN INSPECTION.) • Is the theft-deterrent horn normal?	Yes	Go to the next step.
5		No	Replace the intruder sensor, then go to the next step. (See THEFT-DETERRENT HORN REMOVAL/INSTALLATION.)
6	INSPECT INTRUDER SENSOR • Inspect the intruder sensor. (See INTRUDER SENSOR INSPECTION.) • Is the intruder sensor normal?	Yes	Go to the next step.
6		No	Replace the theft-deterrent horn, then go to the next step. (See INTRUDER SENSOR REMOVAL/INSTALLATION.)
7	DETERMINE IF MALFUNCTION CAUSE IS SYSTEM • Verify what triggered the theft-deterrent system according to the trigger record, and inspect the switch which triggered the system and the related wiring harness. • Is the switch or related wiring harness normal?	Yes	System is normal (explain to the customer that the cause is customer's mis-operation).
7		No	Replace the malfunctioning part.