ROOF MOLDING INSTALLATION

id091600447600


4SD

1.  Install the roof molding to the front T-studs.

am6zzw00012028

2.  Hook the roof molding to clip A and attach the roof molding while pressing it in the direction of the arrow shown in the figure.

3.  Install the roof molding to the rear T-stud.

4.  Press in the clips B installation positions shown in the figure and firmly adhere them to the body.


WGN


With Roof Rail

1.  Install the roof molding to the front T-studs.

am6zzw00012029

2.  Hook the roof molding to clip A and attach the roof molding No.1 while pressing it in the direction of the arrow shown in the figure.

3.  Hook the roof molding to clips B and attach the roof molding No.2 while pressing it in the direction of the arrow shown in the figure.

4.  Press in the clips C installation positions shown in the figure and firmly adhere them to the body.

5.  Install the following parts:

(1)  Roof rail (See ROOF RAIL REMOVAL/INSTALLATION.)
(2)  Headliner (See HEADLINER REMOVAL/INSTALLATION.)
(3)  D-pillar trim (See D-PILLAR TRIM REMOVAL/INSTALLATION.)
(4)  C-pillar trim (See C-PILLAR TRIM REMOVAL/INSTALLATION.)
(5)  Trunk side upper trim (See TRUNK SIDE UPPER TRIM REMOVAL/INSTALLATION.)
(6)  Trunk end trim (See TRUNK END TRIM REMOVAL/INSTALLATION.)
(7)  Trunk side pocket (See TRUNK SIDE POCKET REMOVAL/INSTALLATION.)
(8)  Trunk board (See TRUNK BOARD REMOVAL/INSTALLATION.)
(9)  Rear seat belt lower anchor installation bolt (See REAR SEAT BELT REMOVAL/INSTALLATION.)
(10)  Rear seat cushion (See REAR SEAT CUSHION REMOVAL/INSTALLATION.)
(11)  B-pillar upper trim (See B-PILLAR UPPER TRIM REMOVAL/INSTALLATION.)
(12)  Upper anchor installation bolt on the seat belt (See FRONT SEAT BELT REMOVAL/INSTALLATION.)
(13)  Adjust anchor cover (See FRONT SEAT BELT REMOVAL/INSTALLATION.)
(14)  B-pillar lower trim (See B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
(15)  Rear scuff plate (See REAR SCUFF PLATE REMOVAL/INSTALLATION.)
(16)  Front side trim (RH) (with center display) (See FRONT SIDE TRIM REMOVAL/INSTALLATION.)
(17)  Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
(18)  Assist handle (See ASSIST HANDLE REMOVAL/INSTALLATION.)
(19)  Front map light (See MAP LIGHT REMOVAL/INSTALLATION.)
(20)  Sunvisor (See SUNVISOR REMOVAL/INSTALLATION.)
(21)  A-pillar trim (See A-PILLAR TRIM REMOVAL/INSTALLATION.)
(22)  Sunroof seaming welt (with sunroof system) (See SUNROOF UNIT REMOVAL/INSTALLATION.)

6.  Connect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT i-stop)].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)


Without Roof Rail

1.  Install the roof molding to the front T-studs.

am6zzw00012030

2.  Hook the roof molding to clips A and attach the roof molding while pressing it in the direction of the arrow shown in the figure.

3.  Install the roof molding to the rear T-stud.

4.  Press in the clips B installation positions shown in the figure and firmly adhere them to the body.