DTC U0073:00, U0101:00, U0104:00, U0121:00, U0131:00, U0140:00, U0151:00, U0155:00, U0214:00, U0235:00 [SKYACTIV-G 2.0, SKYACTIV-G 2.5]
id0102h4911000
|
DTC U0073:00 |
CAN system communication error (HS CAN) |
|---|---|
|
DETECTION CONDITION
|
• Malfunction in CAN bus communication line.
Diagnostic support note
• This is a continuous monitor (other).
• The check engine light does not illuminate.
• FREEZE FRAME DATA (Mode 2)/Snapshot data is not available.
• The DTC is stored in the PCM memory.
|
|
FAIL-SAFE FUNCTION
|
Not applicable
|
|
POSSIBLE CAUSE
|
• CAN bus communication line malfunction
• PCM malfunction
|
|
SYSTEM WIRING DIAGRAM
|
Not applicable
|
|
DTC U0101:00 |
CAN communication: communication error to TCM |
|---|---|
|
DETECTION CONDITION
|
• Communication error between the PCM and TCM continues for 5 s or more.
Diagnostic support note
• This is a continuous monitor (other).
• The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.
• FREEZE FRAME DATA (Mode 2)/Snapshot data is available.
• The DTC is stored in the PCM memory.
|
|
FAIL-SAFE FUNCTION
|
• Controls the turbine rotation signal at 0.
• Inhibits the AT torque reduction request.
• Inhibits the i-stop control and flashes the i-stop warning light (amber) (engine stalls while engine is stopped by i-stop control).
|
|
POSSIBLE CAUSE
|
• CAN communication line between PCM and TCM malfunction
• TCM malfunction
• PCM malfunction
|
|
SYSTEM WIRING DIAGRAM
|
Not applicable
|
|
DTC U0104:00 |
CAN communication: communication error to vehicle control module (V/C-module) |
|---|---|
|
DETECTION CONDITION
|
• Communication error between the PCM and vehicle control module (V/C-module) continues for 5 s or more.
Diagnostic support note
• This is a continuous monitor (other).
• The check engine light does not illuminate.
• FREEZE FRAME DATA (Mode 2)/Snapshot data is not available.
• The DTC is stored in the PCM memory.
|
|
FAIL-SAFE FUNCTION
|
• The vehicle control module (V/C-module) function is cancelled.
|
|
POSSIBLE CAUSE
|
• CAN communication line between PCM and vehicle control module (V/C-module) malfunction
• Vehicle control module (V/C-module) malfunction
• PCM malfunction
|
|
SYSTEM WIRING DIAGRAM
|
Not applicable
|
|
DTC U0121:00 |
CAN communication: communication error to DSC HU/CM |
|---|---|
|
DETECTION CONDITION
|
• Communication error between the PCM and DSC HU/CM continues for 5 s or more.
Diagnostic support note
• This is a continuous monitor (other).
• The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.
• FREEZE FRAME DATA (Mode 2)/Snapshot data is available.
• The DTC is stored in the PCM memory.
|
|
FAIL-SAFE FUNCTION
|
• Inhibits the DSC control.
• Inhibits the i-stop control and flashes the i-stop warning light (amber) (engine stalls while engine is stopped by i-stop control).
|
|
POSSIBLE CAUSE
|
• CAN communication line between PCM and DSC HU/CM malfunction
• DSC HU/CM malfunction
• PCM malfunction
|
|
SYSTEM WIRING DIAGRAM
|
Not applicable
|
|
DTC U0131:00 |
CAN communication: communication error to EPS control module |
|---|---|
|
DETECTION CONDITION
|
• Communication error between the PCM and EPS control module continues for 5 s or more.
Diagnostic support note
• This is a continuous monitor (other).
• The check engine light does not illuminate.
• FREEZE FRAME DATA (Mode 2)/Snapshot data is not available.
• The DTC is stored in the PCM memory.
|
|
FAIL-SAFE FUNCTION
|
• Inhibits the i-stop control and flashes the i-stop warning light (amber) (engine stalls while engine is stopped by i-stop control).
|
|
POSSIBLE CAUSE
|
• CAN communication line between PCM and EPS control module malfunction
• EPS control module malfunction
• PCM malfunction
|
|
SYSTEM WIRING DIAGRAM
|
Not applicable
|
|
DTC U0140:00 |
CAN communication: communication error to front body control module (FBCM) |
|---|---|
|
DETECTION CONDITION
|
• Communication error between the PCM and front body control module (FBCM) continues for 5 s or more.
Diagnostic support note
• This is a continuous monitor (other).
• The check engine light does not illuminate.
• FREEZE FRAME DATA (Mode 2)/Snapshot data is not available.
• The DTC is stored in the PCM memory.
|
|
FAIL-SAFE FUNCTION
|
• Inhibits the i-stop control and flashes the i-stop warning light (amber) (engine stalls while engine is stopped by i-stop control).
|
|
POSSIBLE CAUSE
|
• CAN communication line between PCM and front body control module (FBCM) malfunction
• Front body control module (FBCM) malfunction
• PCM malfunction
|
|
SYSTEM WIRING DIAGRAM
|
Not applicable
|
|
DTC U0151:00 |
CAN communication: communication error to SAS control module |
|---|---|
|
DETECTION CONDITION
|
• Communication error between the PCM and SAS control module continues for 5 s or more.
Diagnostic support note
• This is a continuous monitor (other).
• The check engine light does not illuminate.
• FREEZE FRAME DATA (Mode 2)/Snapshot data is not available.
• The DTC is stored in the PCM memory.
|
|
FAIL-SAFE FUNCTION
|
• Inhibits the i-stop control and flashes the i-stop warning light (amber) (engine stalls while engine is stopped by i-stop control).
|
|
POSSIBLE CAUSE
|
• CAN communication line between PCM and SAS control module malfunction
• SAS control module malfunction
• PCM malfunction
|
|
SYSTEM WIRING DIAGRAM
|
Not applicable
|
|
DTC U0155:00 |
CAN communication: communication error to instrument cluster |
|---|---|
|
DETECTION CONDITION
|
• Communication error between the PCM and instrument cluster continues for 5 s or more.
Diagnostic support note
• This is a continuous monitor (other).
• The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.
• FREEZE FRAME DATA (Mode 2)/Snapshot data is available.
• The DTC is stored in the PCM memory.
|
|
FAIL-SAFE FUNCTION
|
• Inhibits the i-stop control and flashes the i-stop warning light (amber) (engine stalls while engine is stopped by i-stop control).
|
|
POSSIBLE CAUSE
|
• CAN communication line between PCM and instrument cluster malfunction
• Instrument cluster malfunction
• PCM malfunction
|
|
SYSTEM WIRING DIAGRAM
|
Not applicable
|
|
DTC U0214:00 |
CAN communication: communication error to start stop unit |
|---|---|
|
DETECTION CONDITION
|
• Communication error between the PCM and start stop unit continues for 5 s or more.
Diagnostic support note
• This is a continuous monitor (other).
• The check engine light does not illuminate.
• FREEZE FRAME DATA (Mode 2)/Snapshot data is not available.
• The DTC is stored in the PCM memory.
|
|
FAIL-SAFE FUNCTION
|
• Inhibits the i-stop control and flashes the i-stop warning light (amber) (engine stalls while engine is stopped by i-stop control).
|
|
POSSIBLE CAUSE
|
• CAN communication line between PCM and start stop unit malfunction
• Start stop unit malfunction
• PCM malfunction
|
|
SYSTEM WIRING DIAGRAM
|
Not applicable
|
|
DTC U0235:00 |
CAN communication: communication error to laser sensor |
|---|---|
|
DETECTION CONDITION
|
• Communication error between the PCM and laser sensor continues for 5 s or more.
Diagnostic support note
• This is a continuous monitor (other).
• The check engine light does not illuminate.
• FREEZE FRAME DATA (Mode 2)/Snapshot data is not available.
• The DTC is stored in the PCM memory.
|
|
FAIL-SAFE FUNCTION
|
• The smart city brake support function is cancelled.
|
|
POSSIBLE CAUSE
|
• CAN communication line between PCM and laser sensor malfunction
• Laser sensor malfunction
• PCM malfunction
|
|
SYSTEM WIRING DIAGRAM
|
Not applicable
|
Diagnostic Procedure