REFRIGERANT LINE REMOVAL/INSTALLATION

id071100803000

L.H.D.

SKYACTIV-G 2.0, SKYACTIV-G 2.5

1. Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].)(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT i-stop)].)

2. Discharge the refrigerant. (See REFRIGERANT CHARGING.)

3. Disconnect the refrigerant pressure sensor connector.

am6zzw00010639

4. Remove in the order indicated in the table. Do not allow compressor oil to spill.

Caution

• If moisture or foreign material enters the refrigeration cycle, cooling ability will be lowered and abnormal noise will occur. Always immediately plug all open fittings after removing any refrigeration cycle parts to keep moisture or foreign material out of the cycle.

am6zzw00010640

1

Cooler hose (HI)

(See Refrigerant Line Installation Note (1).)

(See Refrigerant Line Installation Note (2).)

2

Cooler hose (LO)

(See Refrigerant Line Installation Note (1).)

(See Refrigerant Line Installation Note (2).)

3

Cooler pipe

(See Refrigerant Line Installation Note (1).)

(See Refrigerant Line Installation Note (2).)

5. Install in the reverse order of removal.

6. Perform the refrigerant system performance test. (See REFRIGERANT SYSTEM PERFORMANCE TEST.)

SKYACTIV-D 2.2

1. Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

2. Discharge the refrigerant. (See REFRIGERANT CHARGING.)

3. Disconnect the connector.

am6zzw00010641

4. Detach the fastener.

5. Remove the bolts.

6. Remove the clip.

7. Set the PCM out of the way.

am6zzw00011156

8. Disconnect the refrigerant pressure sensor connector.

am6zzw00010642

9. Remove the nut.

am6zzw00010643

10. Remove the bolt.

11. Remove the bracket.

12. Set the PCM out of the way.

am6zzw00010644

13. Remove in the order indicated in the table. Do not allow compressor oil to spill.

Caution

am6zzw00010645

14. Install in the reverse order of removal.

15. Perform the refrigerant system performance test. (See REFRIGERANT SYSTEM PERFORMANCE TEST.)

R.H.D.

SKYACTIV-G 2.0, SKYACTIV-G 2.5

2. Discharge the refrigerant. (See REFRIGERANT CHARGING.)

3. Remove the plug hole plate. (See PLUG HOLE PLATE REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].)

4. Remove the nut.

ac5wzw00001827

5. Remove the insulator.

6. Disconnect the refrigerant pressure sensor connector.

am6zzw00010639

7. Remove in the order indicated in the table. Do not allow compressor oil to spill.

Caution

am6zzw00010646

8. Install in the reverse order of removal.

9. Perform the refrigerant system performance test. (See REFRIGERANT SYSTEM PERFORMANCE TEST.)

SKYACTIV-D 2.2

1. Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

2. Discharge the refrigerant. (See REFRIGERANT CHARGING.)

3. Remove the engine cover. (See ENGINE COVER REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

4. Remove the nut from underside of vehicle.

ac5wzw00001830

5. Remove the nut from top side of vehicle.

am6zzw00011157

6. Remove the insulator as shown in the figure.

am6zzw00011158

7. Disconnect the connector.

am6zzw00010641

8. Detach the fastener.

9. Remove the bolts.

10. Remove the clip.

11. Set the PCM out of the way.

am6zzw00011156

12. Disconnect the refrigerant pressure sensor connector.

am6zzw00010642

13. Remove the nut.

am6zzw00010643

14. Remove the bolt.

15. Remove the bracket.

16. Set the PCM out of the way.

am6zzw00010644

17. Remove in the order indicated in the table. Do not allow compressor oil to spill.

Caution

am6zzw00010647

18. Install in the reverse order of removal.

19. Perform the refrigerant system performance test. (See REFRIGERANT SYSTEM PERFORMANCE TEST.)

Refrigerant Line Installation Note (1)

1. Apply compressor oil to the O-rings and connect the joints.

2. Tighten the joints.

Block joint type

1. Tighten the joint bolt by hand.

2. Connect the block joint type pipes by grasping the female side of the block with pliers or similar tool and holding firmly, then tighten the connection bolt or nut with a torque wrench.

am6zzw00010648

Refrigerant Line Installation Note (2)

1. After replacing the refrigerant line, add compressor oil to the refrigeration cycle.

• After replacing the cooler hose (HI)

Supplemental oil amount (approx. quantity)

― 1 ml {1 cc, 0.03 fl oz}

• After replacing the cooler hose (LO)

Supplemental oil amount (approx. quantity)

― 3 ml {3 cc, 0.1 fl oz}

• After replacing the cooler pipe

Supplemental oil amount (approx. quantity)

― 1 ml {1 cc, 0.03 fl oz}

1	Cooler hose (HI) (See Refrigerant Line Installation Note (1).) (See Refrigerant Line Installation Note (2).)
2	Cooler hose (LO) (See Refrigerant Line Installation Note (1).) (See Refrigerant Line Installation Note (2).)
3	Cooler pipe (See Refrigerant Line Installation Note (1).) (See Refrigerant Line Installation Note (2).)