DOOR GLASS STOPS BEFORE FULLY OPENING/CLOSING [POWER WINDOW SYSTEMS (EXTERIOR OPEN/CLOSE FUNCTION)]

id090361884400

Description

• Door glass stops before fully opening/closing

Possible cause

• Power window main switch malfunction

• Power window subswitch malfunction

• Power window motor malfunction

• Battery malfunction (Low voltage)

• Door glass improper installation

• Power window initialization procedure error

• Start stop unit malfunction

• Rear body control module (RBCM) malfunction

• LF control unit malfunction

• Keyless receiver malfunction

• Advanced keyless entry system signal reception error (outside operation area, radio signal interference)

Diagnostic Procedure

Step

Inspection

Action

1

•  Operate the door glass in auto/manual by operating the power window main switch/power window subswitch.

•  Does the door glass stop before fully opening/closing using either operation?

Yes

Inspect the following parts, and repair or replace.

•  Power window main switch
(See POWER WINDOW MAIN SWITCH INSPECTION.)

•  Power window subswitch
(See POWER WINDOW SUBSWITCH INSPECTION.)

•  Power window motor
(See POWER WINDOW MOTOR INSPECTION.)

•  Battery (Low voltage)

•  Door glass (Installation condition)

No

Go to the next step.

2

•  Inspect the operation of the door glass by repeating Step 1 above.

•  Does the door glass stop before fully opening/closing while in auto operation?

Yes

Perform the power window initialization procedure.

(See POWER WINDOW SYSTEM INITIALIZATION PROCEDURE.)

No

Go to the next step.

3

•  Open the door glass by operating the transmitter.

•  Does the door glass stop before fully opening?

Yes

Inspect the following parts, and repair or replace.

•  Keyless receiver
(See KEYLESS RECEIVER INSPECTION.)

•  LF control unit
(See LF CONTROL UNIT INSPECTION.)

•  Start stop unit
(See START STOP UNIT INSPECTION.)

•  Rear body control module (RBCM)
(SeeREAR BODY CONTROL MODULE (RBCM) INSPECTION.)

•  Advanced keyless entry system signal reception (the system is in outside operation area and/or influenced radio signal interference intermittently)

No

Go to the next step.

4

•  Close the door glass by operating the transmitter.

•  Does the door glass stop before fully closing?

Yes

Inspect the following parts, and repair or replace.

•  Keyless receiver
(See KEYLESS RECEIVER INSPECTION.)

•  LF control unit
(See LF CONTROL UNIT INSPECTION.)

•  Start stop unit
(See START STOP UNIT INSPECTION.)

•  Rear body control module (RBCM)
(SeeREAR BODY CONTROL MODULE (RBCM) INSPECTION.)

•  Advanced keyless entry system signal reception (the system is in outside operation area and/or influenced radio signal interference intermittently)

No

Reinspect for malfunction recurrence. If the malfunction is not corrected, repeat the procedure from Step 1.

Step	Inspection		Action
1	• Operate the door glass in auto/manual by operating the power window main switch/power window subswitch. • Does the door glass stop before fully opening/closing using either operation?	Yes	Inspect the following parts, and repair or replace. • Power window main switch (See POWER WINDOW MAIN SWITCH INSPECTION.) • Power window subswitch (See POWER WINDOW SUBSWITCH INSPECTION.) • Power window motor (See POWER WINDOW MOTOR INSPECTION.) • Battery (Low voltage) • Door glass (Installation condition)
1		No	Go to the next step.
2	• Inspect the operation of the door glass by repeating Step 1 above. • Does the door glass stop before fully opening/closing while in auto operation?	Yes	Perform the power window initialization procedure. (See POWER WINDOW SYSTEM INITIALIZATION PROCEDURE.)
2		No	Go to the next step.
3	• Open the door glass by operating the transmitter. • Does the door glass stop before fully opening?	Yes	Inspect the following parts, and repair or replace. • Keyless receiver (See KEYLESS RECEIVER INSPECTION.) • LF control unit (See LF CONTROL UNIT INSPECTION.) • Start stop unit (See START STOP UNIT INSPECTION.) • Rear body control module (RBCM) (SeeREAR BODY CONTROL MODULE (RBCM) INSPECTION.) • Advanced keyless entry system signal reception (the system is in outside operation area and/or influenced radio signal interference intermittently)
3		No	Go to the next step.
4	• Close the door glass by operating the transmitter. • Does the door glass stop before fully closing?	Yes	Inspect the following parts, and repair or replace. • Keyless receiver (See KEYLESS RECEIVER INSPECTION.) • LF control unit (See LF CONTROL UNIT INSPECTION.) • Start stop unit (See START STOP UNIT INSPECTION.) • Rear body control module (RBCM) (SeeREAR BODY CONTROL MODULE (RBCM) INSPECTION.) • Advanced keyless entry system signal reception (the system is in outside operation area and/or influenced radio signal interference intermittently)
4		No	Reinspect for malfunction recurrence. If the malfunction is not corrected, repeat the procedure from Step 1.