AFTER REPAIR PROCEDURE [FS5A-EL]

id050221800400

Caution
•  After repairing a malfunction, perform the following procedure to verify that the malfunction has been corrected.
•  When performing this procedure, be sure to drive the vehicle at lawful speed and pay attention to the other vehicles.

1.  Connect the M-MDS to the DLC-2.

am6zzw00002542

2.  After the vehicle is identified, select the following items from the initial screen of the M-MDS.

•  When using the IDS (laptop PC)
1.  Select “SelfTest”.
2.  Select “Modules”.
3.  Select “TCM”.
•  When using the PDS (Pocket PC)
1.  Select “Module Tests”.
2.  Select “TCM”.
3.  Select “SelfTest”.

3.  Verify the DTC according to the directions on the M-MDS screen.

4.  Press the clear button on the DTC screen to clear the DTC.

5.  Perform the following DTC inspections to ensure that the DTCs have been resolved:

DTC No.

inspection
P0706:00, P0707:00, P0708:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle in D range at 20 km/h {12.4 mph} or more for 100 s or more.
iv.  Switch the ignition to off.
v.  Start the engine.
vi.  Drive the vehicle in D range at 20 km/h {12.4 mph} or more for 100 s or more.
vii.  Go to Step 6.
P0711:00
i.  Start the engine then wait 180 s or more.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle in D range, at within 25—59 km/h {16—36 mph}for 90 s or more.
iv.  Drive the vehicle in D range, at 60 km/h {37 mph} for 60 s or more.
v.  Switch the ignition to off.
vi.  Start the engine.
vii.  Drive the vehicle in D range, at within 25—59 km/h {16—36 mph} for 90 s or more.
viii.  Drive the vehicle in D range, at 60 km/h {37 mph} or more for 60 s or more.
ix.  Go to Step 6.
P0712:00, P0713:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle in D range, at 20 km/h {12 mph} or more for 150 s or more.
iv.  Go to Step 6.
P0715:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle in D range, at 41 km/h {25 mph} or more for 0.7 s or more.
iv.  Go to Step 6.
P0720:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions for 4.5 s or more.
•  Turbine speed (TSS PID): 1,500 rpm or more
•  Selector lever position: D range, 1GR
iv.  Switch the ignition to off.
v.  Start the engine.
vi.  Drive the vehicle under the following conditions for 4.5 s or more.
•  Turbine speed (TSS PID): 1,500 rpm or more
•  Selector lever position: D range, 1GR
vii.  Go to Step 6.
P0731:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions 4 times or more.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Selector lever position: D or M range, 1GR
•  Throttle opening angle: 3.17% or more
iv.  Go to Step 6.
P0732:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions 3 times or more.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Selector lever position: D or M range, 2GR
iv.  Go to Step 6.
P0733:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Selector lever position: D or M range, 3GR
iv.  Go to Step 6.
P0734:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions.
•  Vehicle speed (VSS PID): 27 km/h {17 mph} or more
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Selector lever position: D or M range, 4GR
iv.  Go to Step 6.
P0735:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Throttle opening angle: 3.17% or more
•  Selector lever position: D or M range, from 1GR to 5GR
iv.  Go to Step 6.
P0741:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions for 5 s or more.
•  Vehicle speed (VSS PID): 60—100 km/h {38—62 mph}
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Selector lever position: D range, 4GR
iv.  Go to Step 6.
P0742:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions.
•  Vehicle speed (VSS PID): 70 km/h {43 mph} or less
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Selector lever position: D range, 4GR
•  Throttle conditions
―  Throttle opening angle is 6.25% or more and 5 s or more have passed.
―  Throttle opening angle is within 3.13—6.25% and 3 s or more have passed.
―  Throttle opening angle is at closed throttle position and 5 s or more have passed.
iv.  Go to Step 6.
P0744:00
i.  Start the engine.
ii.  Warm up the engine to normal operating temperature.
iii.  Drive the vehicle under the following conditions for 1 s or more.
―  3GR
―  Accelerator pedal position: 15% or less
―  Vehicle speed: 30 km/h {19 mph} or more
iv.  Drive the vehicle under the following conditions for 1 s or more.
―  4GR
―  Accelerator pedal position: 15% or less
―  Vehicle speed: 39 km/h {24 mph} or more
v.  Go to Step 6.
P0753:00, P0758:00, P0763:00, P0768:00, P0773:00, P0778:00, P0841:00, P0883:00, P1783:00, P2709:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle in D range and make sure that the gears shift smoothly from 1GR to 5GR and TCC is operated.
iv.  Switch the ignition to off.
v.  Start the engine.
vi.  Drive the vehicle in D range and make sure that the gears shift smoothly from 1GR to 5GR and TCC is operated.
vii.  Go to Step 6.
P0745:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle in D range.
iv.  Go to Step 6.
P0751:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions for 15 s or more.
•  Vehicle speed (VSS PID): 35 km/h {22 mph} or more
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Selector lever position: D range, 4GR
iv.  Switch the ignition to off.
v.  Start the engine.
vi.  Drive the vehicle under the following conditions for 15 s or more.
•  Vehicle speed (VSS PID): 35 km/h {22 mph} or more
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Selector lever position: D range, 4GR
vii.  Go to Step 6.
P0752:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Selector lever position: D range
iv.  Depress the brake pedal.
v.  Switch the ignition to off.
vi.  Start the engine.
vii.  Selector lever position: D range
viii.  Depress the brake pedal.
ix.  Go to Step 6.
P0756:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions 4 times or more.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Throttle opening angle: 3.17% or more
•  Differential gear case (output) revolution speed (OSS PID): 35 rpm or more
•  Selector lever position: D range, 1GR
iv.  Switch the ignition to off.
v.  Start the engine.
vi.  Drive the vehicle under the following conditions 4 times or more.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Throttle opening angle: 3.17% or more
•  Differential gear case (output) revolution speed (OSS PID): 35 rpm or more
•  Selector lever position: D range, 1GR
vii.  Go to Step 6.
P0757:00, P0766:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions.
•  Vehicle speed (VSS PID): 27 km/h {17 mph} or more
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Throttle opening angle at closed throttle position
•  Differential gear case (output) revolution speed (OSS PID): 35 rpm or more
•  Selector lever position: D range, 2GR and 4GR
iv.  Switch the ignition to off.
v.  Start the engine.
vi.  Drive the vehicle under the following conditions.
•  Vehicle speed (VSS PID): 27 km/h {17 mph} or more
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Throttle opening angle at closed throttle position
•  Differential gear case (output) revolution speed (OSS PID): 35 rpm or more
•  Selector lever position: D range, 2GR and 4GR
vii.  Go to Step 6.
P0761:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions 4 times or more.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Throttle opening angle: 3.17% or more
•  Differential gear case (output) revolution speed (OSS PID): 35 rpm or more
•  Selector lever position: D range, 1GR and 2GR
iv.  Switch the ignition to off.
v.  Start the engine.
vi.  Drive the vehicle under the following conditions 4 times or more.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Throttle opening angle: 3.17% or more
•  Differential gear case (output) revolution speed (OSS PID): 35 rpm or more
•  Selector lever position: D range, 1GR and 2GR
vii.  Go to Step 6.
P0762:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions.
•  Vehicle speed (VSS PID): 25 km/h {16 mph} or more
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Differential gear case (output) revolution speed (OSS PID): 35 rpm or more
•  Selector lever position: D range, 3GR
iv.  Switch the ignition to off.
v.  Start the engine.
vi.  Drive the vehicle under the following conditions.
•  Vehicle speed (VSS PID): 25 km/h {16 mph} or more
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Differential gear case (output) revolution speed (OSS PID): 35 rpm or more
•  Selector lever position: D range, 3GR
vii.  Go to Step 6.
P0767:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions for 5 s or more.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Selector lever position: D range, 3GR
iv.  Switch the ignition to off.
v.  Start the engine.
vi.  Drive the vehicle under the following conditions for 5 s or more.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Selector lever position: D range, 3GR
vii.  Go to Step 6.
P0771:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions for 5 s or more.
•  Vehicle speed (VSS PID): 60—100 km/h {38—62 mph}
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Selector lever position: D range, 4GR
iv.  Switch the ignition to off.
v.  Start the engine.
vi.  Drive the vehicle under the following conditions for 5 s or more.
•  Vehicle speed (VSS PID): 60—100 km/h {38—62 mph}
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Selector lever position: D range, 4GR
vii.  Go to Step 6.
P0772:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions.
•  Vehicle speed (VSS PID): 70 km/h {43 mph} or less
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Selector lever position: D range, 4GR
•  Throttle conditions
―  Throttle opening angle is 6.25% or more and 5 s or more have passed.
―  Throttle opening angle is within 3.13—6.25% and 3 s or more have passed.
―  Throttle opening angle is at closed throttle position and 5 s or more have passed.
iv.  Switch the ignition to off.
v.  Start the engine.
vi.  Drive the vehicle under the following conditions.
•  Vehicle speed (VSS PID): 70 km/h {43 mph} or less
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Selector lever position: D range, 4GR
•  Throttle conditions
―  Throttle opening angle is 6.25% or more and 5 s or more have passed.
―  Throttle opening angle is within 3.13—6.25% and 3 s or more have passed.
―  Throttle opening angle is at closed throttle position and 5 s or more have passed.
vii.  Go to Step 6.
P0777:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions 4 times or more.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Throttle opening angle: 3.17% or more
•  Selector lever position: D range, 5GR
iv.  Switch the ignition to off.
v.  Start the engine.
vi.  Drive the vehicle under the following conditions 4 times or more.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Throttle opening angle: 3.17% or more
•  Selector lever position: D range, 5GR
vii.  Go to Step 6.
P0791:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle in D range at 40 km/h {25 mph} or more for 4.5 s or more.
iv.  Go to Step 6.
P0884:00
i.  Start the engine.
ii.  Idle the engine for 10 s or more.
iii.  Go to Step 7.
P0894:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Depress the brake pedal.
iv.  Throttle opening angle at closed throttle position.
v.  Shift the selector lever from the N position to the D range and hold for 3 s or more.
vi.  Go to Step 7.
P1566:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Depress the brake pedal.
iv.  Throttle opening angle at closed throttle position.
v.  Shift the selector lever from the N position to the D range and hold for 3 s or more.
vi.  Go to Step 7.
P2707:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions 4 times or more.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Throttle opening angle: 3.17% or more
•  Selector lever position: D range, 3GR or 4GR
iv.  Switch the ignition to off.
v.  Start the engine.
vi.  Drive the vehicle under the following conditions 4 times or more.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Throttle opening angle: 3.17% or more
•  Selector lever position: D range, 3GR or 4GR
vii.  Go to Step 6.
P2708:00
i.  Start the engine.
ii.  Warm up the engine and ATX.
iii.  Drive the vehicle under the following conditions 4 times or more.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Throttle opening angle: 3.17% or more
•  Selector lever position: D range, 5GR
iv.  Switch the ignition to off.
v.  Start the engine.
vi.  Drive the vehicle under the following conditions 4 times or more.
•  Turbine speed (TSS PID): 225—4,987 rpm
•  Throttle opening angle: 3.17% or more
•  Selector lever position: D range, 5GR
vii.  Go to Step 6.

6.  Gradually slow down and stop the vehicle.

7.  Make sure that the repaired DTC does not recur.