DTC B11C0:13 [BCM]

id0902f5414100

Malfunction Location

• Driver’s side rear door latch switch circuit malfunction

Detection Condition

• Open circuit detected in driver’s side rear door latch switch with the rear door (driver’s side) closed (driver’s side rear door latch switch on)

Possible Causes

L.H.D.

• Open circuit in wiring harness between driver’s side rear door latch switch connector terminal L and BCM connector terminal 8H

• Open circuit in wiring harness between driver’s side rear door latch switch connector terminal J and body ground

• Driver’s side rear door latch switch malfunction

• BCM malfunction

R.H.D.

• Open circuit in wiring harness between driver’s side rear door latch switch connector terminal B and BCM connector terminal 8F

• Open circuit in wiring harness between driver’s side rear door latch switch connector terminal D and body ground

• Driver’s side rear door latch switch malfunction

• BCM malfunction

System Wiring Diagram

am6zzw00002145

Diagnostic Procedure

Step

Inspection

Action

1

PERFORM DTC INSPECTION

•  Clear DTCs using the M-MDS.
(See CLEARING DTC [BCM].)

•  Perform the BCM DTC inspection using the M-MDS with the rear door (driver’s side) closed (driver’s side rear door latch switch on).
(See DTC INSPECTION [BCM].)

•  Is DTC B11C0:13 displayed?

Yes

Go to the next step.

No

DTC troubleshooting completed.

2

INSPECT DRIVER’S SIDE REAR DOOR LATCH SWITCH CONNECTOR CONDITION

•  Switch the ignition to off.

•  Disconnect the negative battery cable.

•  Disconnect the driver’s side rear door latch switch connector.

•  Inspect the connector and terminals (corrosion, damage, pin disconnection).

•  Is the connector normal?

Yes

Go to the next step.

No

Repair/replace the connector or terminal.

After repair procedure, go to Step 8.

3

INSPECT REAR DOOR LATCH SWITCH CIRCUIT FOR OPEN CIRCUIT

L.H.D.

•  Reconnect the negative battery cable.

•  Measure the voltage at driver’s side rear door latch switch connector terminal L.

•  Can the voltage be measured?

R.H.D.

•  Reconnect the negative battery cable.

•  Measure the voltage at driver’s side rear door latch switch connector terminal B.

•  Can the voltage be measured?

Yes

Go to the next step.

No

Go to Step 6.

4

INSPECT DRIVER’S SIDE REAR DOOR LATCH SWITCH CIRCUIT FOR OPEN CIRCUIT

L.H.D.

•  Inspect for continuity between driver’s side rear door latch switch connector terminal J and body ground.

•  Is there continuity?

R.H.D.

•  Inspect for continuity between driver’s side rear door latch switch connector terminal D and body ground.

•  Is there continuity?

Yes

Go to the next step.

No

Repair/replace the wiring harness.

After repair procedure, go to Step 8.

5

INSPECT DRIVER’S SIDE REAR DOOR LATCH SWITCH

•  Inspect the driver’s side rear door latch switch.
(See REAR DOOR LATCH SWITCH INSPECTION.)

•  Is the driver’s side rear door latch switch normal?

Yes

Go to Step 8.

No

Replace the driver’s side rear door latch switch.

(See REAR DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION.)

After replacement, go to Step 8.

6

INSPECT BCM CONNECTOR CONDITION

•  Disconnect the negative battery cable.

•  Disconnect the BCM connector.

•  Inspect the connector and terminals (corrosion, damage, pin disconnection).

•  Is the connector normal?

Yes

Go to the next step.

No

Repair/replace the connector or terminal.

After repair procedure, go to Step 8.

7

INSPECT BCM

L.H.D.

•  Reconnect the BCM connector.

•  Reconnect the negative battery cable.

•  Measure the voltage at BCM connector terminal 8H.
(See BODY CONTROL MODULE (BCM) INSPECTION.)

•  Is the voltage normal?

R.H.D.

•  Reconnect the BCM connector.

•  Reconnect the negative battery cable.

•  Measure the voltage at BCM connector terminal 8F.
(See BODY CONTROL MODULE (BCM) INSPECTION.)

•  Is the voltage normal?

Yes

Go to the next step.

No

Repair/replace the wiring harness.

After repair procedure, go to the next step.

8

VERIFY DTC

•  Reconnect the disconnected connectors and the negative battery cable.

•  Clear DTCs using the M-MDS.
(See CLEARING DTC [BCM].)

•  Perform the BCM DTC inspection using the M-MDS with the rear door (driver’s side) closed (driver’s side rear door latch switch on).
(See DTC INSPECTION [BCM].)

•  Is the same DTC present?

Yes

Repeat the inspection from Step 1.

If the malfunction recurs, replace the BCM.

(See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION.)

Go to the next step.

No

Go to the next step.

9

VERIFY THAT NO OTHER DTCs ARE PRESENT

•  Are there other DTCs output?

Yes

Perform the corresponding DTC inspection.

No

DTC troubleshooting completed.

Step	Inspection		Action
1	PERFORM DTC INSPECTION • Clear DTCs using the M-MDS. (See CLEARING DTC [BCM].) • Perform the BCM DTC inspection using the M-MDS with the rear door (driver’s side) closed (driver’s side rear door latch switch on). (See DTC INSPECTION [BCM].) • Is DTC B11C0:13 displayed?	Yes	Go to the next step.
1		No	DTC troubleshooting completed.
2	INSPECT DRIVER’S SIDE REAR DOOR LATCH SWITCH CONNECTOR CONDITION • Switch the ignition to off. • Disconnect the negative battery cable. • Disconnect the driver’s side rear door latch switch connector. • Inspect the connector and terminals (corrosion, damage, pin disconnection). • Is the connector normal?	Yes	Go to the next step.
2		No	Repair/replace the connector or terminal. After repair procedure, go to Step 8.
3	INSPECT REAR DOOR LATCH SWITCH CIRCUIT FOR OPEN CIRCUIT L.H.D. • Reconnect the negative battery cable. • Measure the voltage at driver’s side rear door latch switch connector terminal L. • Can the voltage be measured? R.H.D. • Reconnect the negative battery cable. • Measure the voltage at driver’s side rear door latch switch connector terminal B. • Can the voltage be measured?	Yes	Go to the next step.
3		No	Go to Step 6.
4	INSPECT DRIVER’S SIDE REAR DOOR LATCH SWITCH CIRCUIT FOR OPEN CIRCUIT L.H.D. • Inspect for continuity between driver’s side rear door latch switch connector terminal J and body ground. • Is there continuity? R.H.D. • Inspect for continuity between driver’s side rear door latch switch connector terminal D and body ground. • Is there continuity?	Yes	Go to the next step.
4		No	Repair/replace the wiring harness. After repair procedure, go to Step 8.
5	INSPECT DRIVER’S SIDE REAR DOOR LATCH SWITCH • Inspect the driver’s side rear door latch switch. (See REAR DOOR LATCH SWITCH INSPECTION.) • Is the driver’s side rear door latch switch normal?	Yes	Go to Step 8.
5		No	Replace the driver’s side rear door latch switch. (See REAR DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION.) After replacement, go to Step 8.
6	INSPECT BCM CONNECTOR CONDITION • Disconnect the negative battery cable. • Disconnect the BCM connector. • Inspect the connector and terminals (corrosion, damage, pin disconnection). • Is the connector normal?	Yes	Go to the next step.
6		No	Repair/replace the connector or terminal. After repair procedure, go to Step 8.
7	INSPECT BCM L.H.D. • Reconnect the BCM connector. • Reconnect the negative battery cable. • Measure the voltage at BCM connector terminal 8H. (See BODY CONTROL MODULE (BCM) INSPECTION.) • Is the voltage normal? R.H.D. • Reconnect the BCM connector. • Reconnect the negative battery cable. • Measure the voltage at BCM connector terminal 8F. (See BODY CONTROL MODULE (BCM) INSPECTION.) • Is the voltage normal?	Yes	Go to the next step.
7		No	Repair/replace the wiring harness. After repair procedure, go to the next step.
8	VERIFY DTC • Reconnect the disconnected connectors and the negative battery cable. • Clear DTCs using the M-MDS. (See CLEARING DTC [BCM].) • Perform the BCM DTC inspection using the M-MDS with the rear door (driver’s side) closed (driver’s side rear door latch switch on). (See DTC INSPECTION [BCM].) • Is the same DTC present?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the BCM. (See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION.) Go to the next step.
8		No	Go to the next step.
9	VERIFY THAT NO OTHER DTCs ARE PRESENT • Are there other DTCs output?	Yes	Perform the corresponding DTC inspection.
9		No	DTC troubleshooting completed.