NO.3 TRANSMITTER ID CODE CANNOT BE REPROGRAMMED

id0903d2800800

Applied VIN (assumed):

• JMZ SE1736*# 100001-136001

• JMZ SE17N2*# 100001-136001

• JMZ SE17360# 100001-136001

• JMZ SE17N20# 100001-136001

• JM0 FE103100 100001-104076

3

Transmitter ID code cannot be reprogrammed

DESCRIPTION

• Malfunction in transmitter battery, transmitter, keyless receive bracket, keyless receive bracket ground screw, or keyless unit circuit. keyless receive circuit.

POSSIBLE CAUSE

• Malfunction in transmitter battery, transmitter, keyless receive bracket, keyless receive bracket ground screw, or keyless unit, or keyless receive.

Diagnostic procedure

STEP	INSPECTION		ACTION
1	INSPECT TRANSMITTER BATTERY INSTALLATION AND TYPE • Visually inspect the transmitter battery. • Are the below items correct? ― Transmitter battery installation (correct polarity) ― Battery type (CR2025) (Normal type) ― Battery type (CR1620) (Retractable key type)	Yes	Go to the next step.
1		No	Install the transmitter battery properly or replace with the specified transmitter battery (CR2025 or CR1620), then go to Step 13.
2	INSPECT TRANSMITTER BATTERY TERMINALS FOR RUST AND POOR CONNECTION • Visually inspect the transmitter. ― Is there rust on the transmitter battery terminals (positive or negative)? ― Is there poor connection between the terminals and battery?	Yes	Replace the transmitter battery or repair the transmitter battery terminal, then go to Step 13.
2		No	Go to the next step.
3	INSPECT TRANSMITTER BATTERY • Inspect the transmitter battery. • Is the battery voltage normal?	Yes	Go to the next step.
3		No	Replace the transmitter battery, then go to Step 13.
4	INSPECT KEYLESS RECEIVE BRACKET INSTALLATION • Is the keyless receive bracket installed securely?	Yes	Go to the next step.
4		No	Install bracket securely, then go back to Step 6 of KEYLESS ENTRY SYSTEM PRELIMINARY inspection.
5	INSPECT GROUND SCREW INSTALLATION BETWEEN KEYLESS RECEIVE AND KEYLESS RECEIVE BRACKET • Are the keyless receive and keyless receive bracket connected securely to the ground screw?	Yes	Go to the next step.
5		No	Install the screw securely, then go back to Step 6 of KEYLESS ENTRY SYSTEM PRELIMINARY inspection.
6	INSPECT IF MALFUNCTION IS IN TRANSMITTER BATTERY OR ELSEWHERE • Replace with a transmitter battery known to be good. • Does the keyless entry system operate properly?	Yes	Replace the transmitter battery, then go to Step 13.
6		No	Go to the next step.
7	INSPECT IF MALFUNCTION IS IN TRANSMITTER OR KEYLESS UNIT • Reprogram the keyless unit ID code using another known good transmitter. • Does the keyless entry system operate properly?	Yes	Replace the transmitter and reprogram the transmitter ID code, then go to Step 13.
7		No	Go to the next step.
8	INSPECT POWER SUPPLY FUSE • Is the keyless receiver power supply fuse normal?	Yes	Go to the next step.
8		No	Inspect for a short to ground in circuit of blown fuse. Repair or replace if necessary. Install an appropriate amperage fuse, then go to Step 13.
9	INSPECT IF MALFUNCTION IS IN WIRING HARNESS (NO CONTINUITY BETWEEN FUSE BLOCK AND KEYLESS RECEIVER) OR ELSEWHERE • Measure the voltage at the following keyless receiver terminal: ― Power supply signal (terminal A) • Is the voltage B+?	Yes	Go to the next step.
9		No	Repair the wiring harness between the fuse block and keyless receiver, then go to Step 13.
10	INSPECT IF MALFUNCTION IS IN WIRING HARNESS (NO CONTINUITY BETWEEN KEYLESS RECEIVER AND GROUND) OR ELSEWHERE • Is there continuity between keyless receiver connector terminal E and ground?	Yes	Go to the next step.
10		No	Repair the wiring harness between the keyless receiver and ground, then go to Step 13.
11	INSPECT IF MALFUNCTION IS IN WIRING HARNESS (NO CONTINUITY BETWEEN KEYLESS RECEIVER AND KEYLESS UNIT) OR ELSEWHERE • Disconnect the keyless receiver connector and keyless unit. • Is there continuity between the following terminals? ― Terminal B—terminal 2N ― Terminal C—terminal 2P	Yes	Go to the next step.
11		No	Repair the wiring harness between the keyless receiver and keyless unit, then go to Step 13.
12	INSPECT IF MALFUNCTION IS IN WIRING HARNESS (NO CONTINUITY BETWEEN KEYLESS RECEIVER AND KEYLESS UNIT) OR KEYLESS UNIT • Measure the voltage at keyless unit terminal 2N. ― When transmitter operated: • Any transmitter button is operated without key in steering lock (key reminder switch off): 5 V→1.0 V or less • Key is in steering lock (key reminder switch on): 5 V • Is the voltage normal?	Yes	Replace the keyless unit, then go to the next step.
12		No	Replace the keyless receiver, then go to the next step.
13	REINSPECT MALFUNCTION SYMPTOM AFTER REPAIR • Does the keyless entry system operate properly?	Yes	Troubleshooting completed. Explain repairs to the customer.
13		No	Reinspect the malfunction symptoms, then repeat from Step 1 if the malfunction recurs.

Applied VIN (assumed):

• JMZ SE1736*# 136002-

• JMZ SE17N2*# 136002-

• JMZ SE17360# 136002-

• JMZ SE17N20# 136002-

• JM0 FE103100 104077-

3

Transmitter ID code cannot be reprogrammed

DESCRIPTION

• Malfunction in transmitter battery, transmitter, keyless receive bracket, keyless receive bracket ground screw, or keyless unit circuit.

POSSIBLE CAUSE

• Malfunction in transmitter battery, transmitter, keyless receive bracket, keyless receive bracket ground screw, or keyless unit.

Diagnostic procedure

STEP	INSPECTION		ACTION
1	INSPECT TRANSMITTER BATTERY INSTALLATION AND TYPE • Visually inspect the transmitter battery. • Are the below items correct? ― Transmitter battery installation (correct polarity) ― Battery type (CR1620)	Yes	Go to the next step.
1		No	Install the transmitter battery properly or replace with the specified transmitter battery (CR1620), then go to Step 8.
2	INSPECT TRANSMITTER BATTERY TERMINALS FOR RUST AND POOR CONNECTION • Visually inspect the transmitter. ― Is there rust on the transmitter battery terminals (positive or negative)? ― Is there poor connection between the terminals and battery?	Yes	Replace the transmitter battery or repair the transmitter battery terminal, then go to Step 8.
2		No	Go to the next step.
3	INSPECT TRANSMITTER BATTERY • Inspect the transmitter battery. • Is the battery voltage normal?	Yes	Go to the next step.
3		No	Replace the transmitter battery, then go to Step 8
4	INSPECT KEYLESS RECEIVE BRACKET INSTALLATION • Is the keyless receive bracket installed securely?	Yes	Go to the next step.
4		No	Install bracket securely, then go back to Step 6 of KEYLESS ENTRY SYSTEM PRELIMINARY inspection.
5	INSPECT GROUND SCREW INSTALLATION BETWEEN KEYLESS RECEIVE AND KEYLESS RECEIVE BRACKET • Are the keyless receive and keyless receive bracket connected securely to the ground screw?	Yes	Go to the next step.
5		No	Install the screw securely, then go back to Step 6 of KEYLESS ENTRY SYSTEM PRELIMINARY inspection.
6	INSPECT IF MALFUNCTION IS IN TRANSMITTER BATTERY OR ELSEWHERE • Replace with a transmitter battery known to be good. • Does the keyless entry system operate properly?	Yes	Replace the transmitter battery, then go to Step 8.
6		No	Go to the next step.
7	INSPECT IF MALFUNCTION IS IN TRANSMITTER OR KEYLESS UNIT • Reprogram the keyless unit ID code using another known good transmitter. • Does the keyless entry system operate properly?	Yes	Replace the transmitter and reprogram the transmitter ID code, then go to Step 8.
7		No	Go to the next step.
8	REINSPECT MALFUNCTION SYMPTOM AFTER REPAIR • Does the keyless entry system operate properly?	Yes	Troubleshooting completed. Explain repairs to the customer.
8		No	Reinspect the malfunction symptoms, then repeat from Step 1 if the malfunction recurs.

3	Transmitter ID code cannot be reprogrammed
DESCRIPTION	• Malfunction in transmitter battery, transmitter, keyless receive bracket, keyless receive bracket ground screw, or keyless unit circuit. keyless receive circuit.
POSSIBLE CAUSE	• Malfunction in transmitter battery, transmitter, keyless receive bracket, keyless receive bracket ground screw, or keyless unit, or keyless receive.