DTC C1095[L3]

id040232802900

DTC

C1095

Pump motor, motor relay

DETECTION CONDITION

•  ABS motor monitor signal does not correspond to ABS HU/CM OFF signal.

•  ABS motor monitor signal does not correspond to ABS HU/CM ON signal.

•  ABS motor monitor OFF signal is input within specified time limit when motor signal from the ABS HU/CM is switched from ON to OFF.

POSSIBLE CAUSE

•  ABS 60 A fuse malfunction

•  Open circuit or short to ground in wiring harness between ABS HU/CM terminal AT and battery

•  Open circuit in the wiring harness between ABS HU/CM terminal B and body ground

•  Open or short circuit in ABS HU/CM internal motor relay, or stuck motor relay

•  Open or short circuit in ABS HU/CM internal pump motor, or frozen pump motor

•  Poor connection at connectors (female terminal)

Diagnostic Procedure

STEP	INSPECTION		ACTION
1	INSPECT ABS FUSE CONDITION • Is the ABS fuse (ABS 60A) normal?	Yes	Go to the next step.
1		No	Replace the ABS fuse, then go to Step 6.
2	VERIFY PUMP MOTOR OPERATION • Turn the ignition switch off. • Connect the M-MDS to the DLC-2. • Turn the ignition switch to the ON position. • Access PMP_MOTOR active command modes using the M-MDS. • Does the pump motor operate?	Yes	Go to the next step.
2		No	After replacing the ABS HU/CM, go to Step 6. (See ABS HU REMOVAL/INSTALLATION.)
3	INSPECT MOTOR RELAY POWER SUPPLY FOR OPEN CIRCUIT • Turn the ignition switch off. • Disconnect the ABS HU/CM connectors. • Inspect for continuity between ABS HU/CM terminal AT and the positive battery terminal. • Is there continuity?	Yes	Go to the next step.
3		No	Repair or replace the wiring harness, then go to Step 6.
4	INSPECT MOTOR RELAY POWER SUPPLY FOR SHORT CIRCUIT • Inspect for continuity between ABS HU/CM terminal AT and body ground. • Is there continuity?	Yes	Repair or replace the wiring harness, then go to Step 6.
4		No	Go to the next step.
5	INSPECT PUMP MOTOR GROUND FOR OPEN CIRCUIT • Inspect for continuity between ABS HU/CM terminal B and body ground. • Is there continuity?	Yes	Go to the next step.
5		No	After repairing or replacing the wiring harness, go to the next step.
6	VERIFY THAT THE SAME DTC IS NOT PRESENT • Reconnect all disconnected connectors. • Clear the DTC from the memory. (See ON-BOARD DIAGNOSIS[L3].) • Start the engine and drive the vehicle at 10 km/h {6.2 mph} or more. • Is the same DTC present?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the ABS HU/CM, then go to the next step. (See ABS HU REMOVAL/INSTALLATION.)
6		No	Go to the next step. (See ABS HU REMOVAL/INSTALLATION.)
7	VERIFY THAT NO OTHER DTCS ARE PRESENT • Are any other DTCs present?	Yes	Go to the applicable DTC inspection. (See ON-BOARD DIAGNOSIS[L3].)
7		No	DTC inspection completed.

DTC	C1095		Pump motor, motor relay
DETECTION CONDITION		• ABS motor monitor signal does not correspond to ABS HU/CM OFF signal. • ABS motor monitor signal does not correspond to ABS HU/CM ON signal. • ABS motor monitor OFF signal is input within specified time limit when motor signal from the ABS HU/CM is switched from ON to OFF.
POSSIBLE CAUSE		• ABS 60 A fuse malfunction • Open circuit or short to ground in wiring harness between ABS HU/CM terminal AT and battery • Open circuit in the wiring harness between ABS HU/CM terminal B and body ground • Open or short circuit in ABS HU/CM internal motor relay, or stuck motor relay • Open or short circuit in ABS HU/CM internal pump motor, or frozen pump motor • Poor connection at connectors (female terminal)