Instrument Panel (I/P) Retainer Replacement

Instrument Panel (I/P) Retainer Replacement

Removal Procedure

Caution: A deployed dual stage inflator module will look the same whether one or both stages were used, always assume a deployed dual stage inflator module has an active stage 2. Improper handling or servicing can activate the inflator module and cause personal injury.

Caution: Refer to SIR Inflator Module Handling and Storage Caution .

Caution: Refer to SIR Caution .

1. Disable the frontal SIR system. Refer to SIR Disabling and Enabling Zone 3 and SIR Disabling and Enabling Zone 5 in SIR.
2. Remove the I/P upper trim panel. Refer to Trim Panel Replacement - Instrument Panel (I/P) Upper (Service and Repair).
3. Remove the I/P compartment. Refer to Compartment Replacement - Instrument Panel (I/P) (Service and Repair).




4. Remove the I/P cluster screws
5. Pull rearward to remove the I/P cluster.




6. Remove the radio screws.
7. Remove the radio.




8. Disconnect the radio antenna, the ground strap, and the electrical connectors.




9. Position the front seats rearward.
10. Reach under the front seats to access the lower console screws.
11. Remove the console screws.




12. Remove the cup holder.




13. Lift the rear of the center floor console.
14. Disconnect the electrical connector tot he auxiliary power outlet.
15. Slide the console rearward.




16. Remove the center trim plate from the front console.




17. Remove the front console screws from the right and the left trim panels.
18. Remove the front console trim panels.




19. Remove the screws from the right and the left air outlet ducts.
Remove the outlet ducts.




20. Remove the I/P cluster electrical connector from the slot in the retainer.




21. Remove the screw from the radio ground strap.
22. Remove the radio ground strap.
23. Slide the I/P electrical center off of the tabs on the I/P bracket.




24. Disconnect the body control module (BCM) electrical connector.
25. Remove the DLC by pressing the tabs and pushing the DLC through the I/P retainer.
26. Remove the front carpet retainers. Refer to Carpet Retainer Replacement - Front (Service and Repair) in Interior Trim.




27. Remove the bolts from the passenger SIR system. Access these bolts by reaching through the I/P retainer in the radio area or through the air outlet area.




28. Disconnect the I/P ground connections from the I/P.
29. Remove the retainer nuts and bolts.
30. Remove the I/P retainer from the vehicle.

Installation Procedure





Important: Insulators are required between the I/P retainer and the cross car beam.


1. Verify that an insulator is present at each interface of the I/P retainer to the cross car beam. Install insulators where necessary.
2. Install the I/P retainer by aligning the center 4-way locator first and then the outboard up/down locators with the corresponding holes in the cross car beam.

Notice: Refer to Fastener Notice in Cautions and Notices.

3. Beginning in the center of the I/P, install the I/P retainer nuts and bolts.

Tighten the bolts to 10 Nm (89 lb in).

4. Connect the I/P grounds to the I/P.




5. Position the passenger side frontal SIR component.
6. Install the bolts to the SIR component.

Tighten the bolts to 10 Nm (89 lb in).




7. Install the front carpet retainers. Refer to Carpet Retainer Replacement - Front (Service and Repair) in Interior Trim.
8. Install the DLC in the I/P retainer.




9. Connect the BCM wiring to the BCM.




10. Position the I/P electrical center on the H-brace bracket tabs.
11. Position the radio ground strap.
12. Install the screw to the radio ground strap.

Tighten the bolts to 10 Nm (89 lb in).




13. Install the I/P cluster electrical connector into the slot in the I/P retainer.




14. Position the right and the left air outlet ducts.
15. Install the screws to the outlet ducts.

Tighten the screws to 2.5 Nm (22 lb in).




16. Position the right and the left trim panels on the front console.
17. Install the screws to the front console trim panels.

Tighten the screws to 2.5 Nm (22 lb in).




18. Position the center trim plate to the front console. Push on the plate until the trim clips engage.




19. Lift the rear of the center floor console.
20. Connect the electrical connector to the auxiliary power outlet.
21. Reposition the center console.




22. Install the cup holder to the center console.

Tighten the screw to 2.5 Nm (22 lb in).




23. Position the front seats rearward.
24. Reach under the front seats to access the lower console screws.
25. Install the center console screws.

Tighten the screw to 2.5 Nm (22 lb in).




26. Connect the radio antenna, the ground strap, and the electrical connector.




27. Position the radio in the I/P retainer.
28. Install the radio screws.

Tighten the screws to 2.5 Nm (22 lb in).




29. Position the I/P cluster and install by pushing the cluster forward.
30. Install the cluster screws.

Tighten the screws to 2 Nm (18 lb in).

31. Install the I/P compartment. Refer to Compartment Replacement - Instrument Panel (I/P) (Service and Repair).
32. Install the I/P upper trim panel. Refer to Trim Panel Replacement - Instrument Panel (I/P) Upper (Service and Repair).
33. Enable the frontal SIR system. Refer to SIR Disabling and Enabling Zone 3 and SIR Disabling and Enabling Zone 5 in SIR.