Part 2

INTERIOR PANELS / TRIM: ROOF HEADLINING: INSTALLATION - Continued

51. INSTALL NO. 2 ROOF LINING TRIM COVER (w/ Rear Seat Entertainment System)
(a) Attach the 4 claws to install the cover.
52. INSTALL MAP LIGHT ASSEMBLY
(a) Connect the connector.
(b) Attach the 2 clips and 2 guides to install the map light.
(c) Install the 2 screws.
(d) Attach the 2 claws to close the 2 covers.

53. INSTALL REAR UPPER PILLAR GARNISH LH

(a) Attach the 5 clips to install the rear upper pillar garnish.

(b) Install the seat belt shoulder anchor with the bolt.
Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)

(c) Attach the 2 claws to close the seat belt shoulder anchor cover.
54. INSTALL REAR UPPER PILLAR GARNISH RH
HINT: Use the same procedures described for the LH side.

55. INSTALL REAR FRONT QUARTER TRIM GARNISH LH
(a) Pass the seat belt anchor through the quarter trim garnish.
(b) Attach the clip and 2 guides to install the quarter trim garnish.
(c) Install the screw.
56. INSTALL REAR FRONT QUARTER TRIM GARNISH RH
HINT: Use the same procedures described for the LH side.

57. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

HINT: When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.

(a) Connect the thermistor connector, power outlet socket connector rear seat lock control lever cable.
(b) Attach the 18 clips and 2 claws to install the quarter trim panel.
(c) Install the screw, clip and bolt.
for bolt - Torque: 12 Nm (122 kgf-cm, 9 ft-lbf)

(d) Install the rear No. 2 seat belt anchor with the bolt.
Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)
NOTE: Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

(e) Install the rear No. 1 seat belt anchor with the bolt.
Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)

(f) Attach the 3 claws to install the cover.
58. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT: When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.

(a) Connect the thermistor connector and rear seat lock control lever cable.
(b) Attach the 16 clips and 2 claws to install the quarter trim panel.
(c) Install the screw, clip and bolt.
for bolt - Torque: 12 Nm (122 kgf-cm, 9 ft-lbf)

(d) Install the rear No. 2 seat belt anchor with the bolt.
Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)

(e) Attach the 3 claws to install the cover.

(f) Install the rear No. 1 seat belt anchor with the bolt.
Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)

(g) Attach the 3 claws to install the cover.

59. INSTALL REAR SEAT COVER CAP
HINT: Use the same procedures to install the rear seat cover cap on the other side.

(a) Attach the 3 claws to install the rear seat cover cap.

60. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
HINT: Use the same procedure to install the luggage compartment trim hook on the other side.

(a) Install the luggage compartment trim hook by turning it clockwise.

61. INSTALL CENTER PILLAR GARNISH LH
(a) Pass the seat belt anchor through the center pillar garnish.
(b) Attach the 2 clips and 2 guides to install the center pillar garnish.
(c) Install the bolt.
62. INSTALL CENTER PILLAR GARNISH RH
HINT: Use the same procedures described for the LH side.

63. INSTALL REAR ASSIST GRIP ASSEMBLY

HINT: Use the same procedure to install the rear assist grip on the other side.

(a) Attach the 2 claws to install the rear assist grip.
(b) Install the 2 bolts.

(c) Attach the 4 claws to install the 2 assist grip plugs.
64. INSTALL CENTER LOWER PILLAR GARNISH LH
HINT:
- When installing the center lower pillar garnish, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.
- After moving the front seat, disconnect the cable from the negative (-) battery terminal.

(a) Attach the 2 claws and 7 clips to install the center lower pillar garnish.

(b) Install the seat belt anchor with the bolt.
Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)
65. INSTALL CENTER LOWER PILLAR GARNISH RH
HINT:
- When installing the center lower pillar garnish, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.
- After moving the front seat, disconnect the cable from the negative (-) battery terminal.

(a) Attach the 2 claws and 7 clips to install the center lower pillar garnish.

(b) Install the seat belt anchor with the bolt.
Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)
(c) Connect the connector.
66. INSTALL CENTER PILLAR GARNISH COVER LH
HINT:
- When installing the center pillar garnish cover, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.
- After moving the front seat, disconnect the cable from the negative (-) battery terminal.

(a) Attach the 2 clips and 2 guides to install the cover.
67. INSTALL CENTER PILLAR GARNISH COVER RH
HINT: Use the same procedures described for the LH side.

68. INSTALL FRONT PILLAR GARNISH LH
(a) Connect the speaker connector.
(b) Attach the clip and 3 guides to install the front pillar garnish.
69. INSTALL FRONT PILLAR GARNISH RH
HINT: Use the same procedures described for the LH side.

70. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY

HINT: Use the same procedure to install the front assist grip on the other side.

(a) Attach the 2 claws to install the front assist grip.
(b) Install the 2 bolts.

71. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE
(a) Attach the 6 clips to install the support plate.

72. INSTALL REAR DOOR SCUFF PLATE LH
(a) Attach the 3 claws and 4 clips to install the scuff plate.
(b) Install the screw.
73. INSTALL REAR DOOR SCUFF PLATE RH
HINT: Use the same procedures described for the LH side.

74. INSTALL REAR STEP COVER
HINT: Use the same procedure to install the step cover on the other side.

(a) Attach the 2 claws to install the step cover.

75. INSTALL FRONT DOOR SCUFF PLATE LH
(a) Attach the 7 claws and 4 clips to install the scuff plate.
76. INSTALL FRONT DOOR SCUFF PLATE RH
HINT: Use the same procedures described for the LH side.

77. INSTALL REAR NO. 2 SEAT ASSEMBLY LH
(a) Install the rear No. 2 seat assembly LH Installation.
78. INSTALL REAR NO. 2 SEAT ASSEMBLY RH
HINT: Use the same procedures described for the LH side.

79. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL