Reassembly

EXTERIOR PANELS / TRIM: FRONT BUMPER: REASSEMBLY

1. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH

(a) Engage the guide and install the front side member bracket sub-assembly LH.

(b) Install the 4 bolts.

Torque : 50 Nm (510 kgf-cm, 37 ft-lbf)

2. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH

HINT
Use the same procedure for the RH side and LH side.

3. INSTALL FRONT BUMPER SIDE SUPPORT LH

(a) Engage the 2 claws and install the front bumper side support LH.

(b) Install the bolt and screw.

Torque : 5.4 Nm (55 kgf-cm, 48 in-lbf)

4. INSTALL FRONT BUMPER SIDE SUPPORT RH

HINT
Use the same procedure for the RH side and LH side.

5. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

(a) Install the front bumper reinforcement sub-assembly with the 6 bolts.

Torque : 34 Nm (347 kgf-cm, 25 ft-lbf)

(b) Engage the 7 clamps.

6. INSTALL FRONT BUMPER ENERGY ABSORBER

(a) Engage the 2 guides to install the front bumper energy absorber.

7. INSTALL NO. 1 LOWER RADIATOR GRILLE

(a) Engage the 16 claws to install the No. 1 lower radiator grille.

8. INSTALL FRONT BUMPER HOLE COVER LH

(a) Engage the hook.

(b) Engage the 2 claws and install the front bumper hole cover LH.

9. INSTALL FRONT BUMPER HOLE COVER RH

HINT
Use the same procedure for the RH side and LH side.

10. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY LH Installation

11. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY RH

HINT
Use the same procedure for the RH side and LH side.

12. INSTALL FOG LIGHT COVER LH

(a) Engage the 4 claws and install the fog light cover LH.

13. INSTALL FOG LIGHT COVER RH

HINT
Use the same procedure for the RH side and LH side.

14. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light) Installation

15. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT
Use the same procedure for the RH side and LH side.

16. INSTALL FRONT FENDER LINER RETAINER

(a) Engage the claw and install the front fender liner retainer.

HINT
Use the same procedure for the RH side and LH side.

17. INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY

(a) Engage the 2 pins and 4 claws, and install the radiator grille emblem assembly.

(b) Install the 2 screws.

Torque : 3.0 Nm (31 kgf-cm, 27 in-lbf)

18. INSTALL RADIATOR GRILLE

(a) Engage the 12 claws and install the radiator grille.

(b) Install the 4 clips.

19. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ Advanced Parking Guidance System) Installation

20. INSTALL NO. 1 ULTRASONIC SENSOR (w/ Advanced Parking Guidance System) Installation

21. INSTALL ENGINE ROOM NO. 3 WIRE

(a) Engage the 7 clamps.

(b) Engage the 3 clamps.

22. INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)

(a) Engage the 5 clamps and install the headlight cleaner hose.

23. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System) Installation

24. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT
Use the same procedure for the RH side and LH side.

25. INSTALL HEADLIGHT CLEANER WASHER NOZZLE LH (w/ Headlight Cleaner System) Removal

26. INSTALL HEADLIGHT CLEANER WASHER NOZZLE RH (w/ Headlight Cleaner System)

HINT
Use the same procedure for the RH side and LH side.

27. INSTALL HOOD TO FRONT END PANEL SEAL

(a) Engage the 2 clips and install the new hood to front end panel seal.

(b) Install the 7 clips.

28. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET

(a) Install the front bumper extension mounting bracket with the 2 screws.