Reassembly

SEAT: REAR NO. 2 SEAT ASSEMBLY: REASSEMBLY

HINT
* Use the same procedures for the RH side and LH side.
* The procedures listed below are for the LH side.
1. INSTALL SEAT LOCK RELEASE BAND

(a) Install the band with nut.

HINT
After installing the band, feed it through the seatback frame hole towards the rear of the vehicle.

2. INSTALL RECLINING LOCK RELEASE BAND

HINT
Use the same procedures described for the LH side.

3. INSTALL SEATBACK LOCK CONTROL CABLE ASSEMBLY

(a) Install the cable to the seatback frame as shown in the illustration.

4. INSTALL REAR SEAT RECLINING INNER COVER LH

(a) Attach the 2 claws to install the inner cover.

5. INSTALL REAR SEAT RECLINING INNER COVER RH

HINT
Use the same procedures described for the LH side.

6. INSTALL REAR NO. 2 SEATBACK COVER

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, avoid wrinkling the cover.
(a) Using hog ring pliers, install the seatback cover to the seatback pad with 3 new hog rings.

(b) Install the seatback cover (with pad) to the seatback frame.

(c) Attach the 4 claws to install the 2 headrest supports.

(d) Using hog ring pliers, install 19 new hog rings.

7. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH

(a) Pass the 2 release bands through the 2 holes in the seatback board carpet.

(b) Attach the 9 clips to install the carpet.

HINT
Make sure that the release band is not inside the seatback board carpet.

8. INSTALL REAR SEATBACK LOCK CONTROL BEZEL

(a) Pass the 2 release bands through the 2 holes in the 2 bezels.

(b) Attach the 2 claws to install the 2 bezels.

(c) Install the 2 screws.

(d) Install the 4 seatback lock hooks.

9. INSTALL REAR NO. 2 SEAT HEADREST ASSEMBLY

10. INSTALL REAR SEAT CUSHION WIRE SUB-ASSEMBLY

(a) Install the wire with the nut.

Torque : 18 Nm (184 kgf-cm, 13 ft-lbf)

11. INSTALL SEAT LOCK CONTROL CABLE ASSEMBLY

(a) Install the 5 cables to the seat cushion spring as shown in the illustration.

(b) Clamp the cables to the seat cushion spring with 4 new cable ties as shown in the illustration.

(d) Attach the 2 clamps of the cable tie to the seat cushion spring.

12. INSTALL REAR NO. 2 SEAT CUSHION COVER LH

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, avoid wrinkling the cover.
(a) Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 5 new hog rings.

(b) Attach the hooks and install the seat cushion cover (with pad) to the seat cushion spring.

(d) Install the 2 clips.

13. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH Installation

14. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY

(a) Install the seat cushion to the seatback with the 4 bolts.

Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)

(b) Connect the seat lock control cable of the RH side to the seatback as shown in the illustration.

(d) Close the seat cushion cover and install the 2 clips.

15. INSTALL NO. 1 REAR SEAT RECLINING COVER LH

(a) Attach the 5 claws to install the cover.

(b) Install the 2 screws.

16. INSTALL NO. 2 REAR SEAT RECLINING COVER LH

(a) Attach the clip and 5 claws to install the cover.

(b) Install the 2 screws.