Pinpoint Tests AD: DTCs B00C0:12, B00C0:13 and B00C0:1A
Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS)
Pinpoint Tests
Pinpoint Test AD: DTCs B00C0:12, B00C0:13 and B00C0:1A
Refer to Wiring Diagram Set 46, Supplemental Restraint System for schematic and connector information. Diagrams By Number
Normal Operation
The Occupant Classification System Module (OCSM) monitors Occupant Classification System (OCS) weight sensor bolt "A" circuitry for faults. If the OCSM detects a fault, it stores DTC B00C0:12, B00C0:13 or B00C0:1A in memory and sends a message to the Restraints Control Module (RCM).
The RCM stores DTC B00A0:09 in memory and sends a message to the Instrument Panel Cluster (IPC) to illuminate the air bag warning indicator.
- DTC B00C0:12 (Passenger Seat Occupant Classification Sensor "A": Circuit Short To Battery) - A fault is indicated when the OCSM measures voltage on the OCS weight sensor bolt "A" signal circuit above 4.85 volts. An open sensor return circuit also sets this DTC.
- DTC B00C0:13 (Passenger Seat Occupant Classification Sensor "A": Circuit Open) - A fault is indicated when the OCSM measures resistance greater than 498,200 ohms on the OCS weight sensor bolt "A" signal circuit.
- DTC B00C0:1A (Passenger Seat Occupant Classification Sensor "A": Circuit Resistance Below Threshold) - A fault is indicated when the OCSM measures resistance less than 441,800 ohms on the OCS weight sensor bolt "A" signal circuit.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- OCS weight sensor bolt "A"
- OCSM
PINPOINT TEST AD: DTCs B00C0:12, B00C0:13 AND B00C0:1A
WARNING: Never probe the electrical connectors on air bag, Safety Canopy(R) or side air curtain modules. Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
WARNING: Never disassemble or tamper with safety belt buckle/retractor pretensioners or adaptive load limiting retractors or probe the electrical connectors. Failure to follow this instruction may result in the accidental deployment of the safety belt pretensioners or adaptive load limiting retractors which increases the risk of serious personal injury or death.
NOTICE: Use the correct probe adapter(s) from the Flex Probe Kit when taking measurements. Failure to use the correct probe adapter(s) may damage the connector.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test. Inspection and Verification
NOTE: The OCS weight sensor bolt(s) are 3 wire sensors and cannot be tested using a multi-meter.
NOTE: Only disconnect or reconnect Supplemental Restraint System (SRS) components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS.
NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford Catalog Advantage(TM) or equivalent to make sure the correct component is being installed. If an incorrect SRS component is installed, DTCs may set.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
-------------------------------------------------
AD1 RETRIEVE OCSM DTCs
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - OCSM.
- Was DTC B00C0:12, B00C0:13 or B00C0:1A retrieved on-demand during self-test?
Yes
This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test. GO to AD2.
No
This is an intermittent fault when present as a Continuous Memory Diagnostic Trouble Code (CMDTC) only. GO to AD11.
-------------------------------------------------
AD2 CHECK THE SEAT WIRING AND CONNECTORS
- Ignition OFF.
- WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
- Carry out a thorough inspection of the OCS system wiring, terminals and connectors, weight sensor bolt connector and connection, wiring harness routing and the related seat wiring harness and body wiring harness terminals and connectors.
- Were any problems noted?
Yes
DEPOWER the SRS. REFER to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
REPAIR the seat connectors and wiring as needed.
Refer to Wiring Diagram Set 5, Connector Repair Procedures for schematic and connector information. Diagrams By Number
GO to AD12.
No
For DTC B00C0:12, GO to AD3.
For DTC B00C0:13, GO to AD5.
For DTC B00C0:1A, GO to AD8.
-------------------------------------------------
AD3 CHECK THE OCS WEIGHT SENSOR BOLT "A" SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE
- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: Passenger Seat Side Air Bag Module C339.
- Disconnect: OCS Weight Sensor Bolt "A" C3324.
- Repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Measure the voltage between OCS weight sensor bolt "A" C3324-3, circuit VR211 (WH/BN), harness side and ground.
- Is any voltage present?
Yes
REPAIR circuit VR211 (WH/BN).
Refer to Wiring Diagram Set 5 for schematic and connector information. Diagrams By Number
GO to AD12.
No
GO to AD4.
-------------------------------------------------
AD4 CHECK THE OCS WEIGHT SENSOR BOLT "A" RETURN CIRCUIT FOR AN OPEN
- Ignition OFF.
- WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
- Measure the resistance between OCS weight sensor bolt "A" C3324-2, circuit RR140 (GN/OG), harness side and ground.
- Is the resistance less than 5 ohms?
Yes
GO to AD10.
No
REPAIR circuit RR140 (GN/OG).
Refer to Wiring Diagram Set 5 for schematic and connector information. Diagrams By Number
GO to AD12.
-------------------------------------------------
AD5 CHECK THE OCS WEIGHT SENSOR BOLT "A" FOR A FAULT STATUS CHANGE (OPEN INDICATED)
NOTE: This pinpoint test step attempts to change the fault reported by the OCSM by inducing a different fault condition. If the fault reported changes, this indicates the OCSM is functioning correctly and is not the source of the fault.
- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: Passenger Seat Side Air Bag Module C339.
- Disconnect: OCS Weight Sensor Bolt "A" C3324.
- Connect a fused jumper wire between OCS weight sensor bolt "A" C3324-3, circuit VR211 (WH/BN), harness side and C3324-2, circuit RR140 (GN/OG), harness side.
- Repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - OCSM.
- DIAGNOSTIC TIP: When viewing DTCs with the OCS weight sensor bolt "A" circuits shorted together, a low resistance circuit fault is normally retrieved.
- Did the on-demand DTC change from B00C0:13 to B00C0:1A?
Yes
REMOVE the fused jumper wire and INSTALL a new seat track assembly with OCS weight sensor bolts. REFER to Seating Seat Track. GO to AD12.
No
REMOVE the fused jumper wire and GO to AD6.
-------------------------------------------------
AD6 CHECK THE OCS WEIGHT SENSOR BOLT "A" SIGNAL CIRCUIT FOR AN OPEN
- Ignition OFF.
- Disconnect: OCSM C3159.
- Measure the resistance between OCSM C3159-3, circuit VR211 (WH/BN), harness side and OCS weight sensor bolt "A" C3324-3, circuit VR211 (WH/BN), harness side.
- Is the resistance less than 0.5 ohm?
Yes
GO to AD7.
No
REPAIR circuit VR211 (WH/BN).
Refer to Wiring Diagram Set 5 for schematic and connector information. Diagrams By Number
GO to AD12.
-------------------------------------------------
AD7 CHECK THE OCS WEIGHT SENSOR BOLT "A" VREF CIRCUIT FOR AN OPEN
- Measure the resistance between OCS weight sensor bolt "A" C3324-1, circuit CR140 (YE/GN), harness side and OCSM C3159-2, circuit CR140 (YE/GN), harness side.
- Is the resistance less than 0.5 ohm?
Yes
GO to AD10.
No
REPAIR circuit CR140 (YE/GN).
Refer to Wiring Diagram Set 5 for schematic and connector information. Diagrams By Number
GO to AD12.
-------------------------------------------------
AD8 CHECK THE OCS WEIGHT SENSOR BOLT "A" FOR A FAULT STATUS CHANGE (RESISTANCE BELOW THRESHOLD INDICATED)
NOTE: This pinpoint test step attempts to change the fault reported by the OCSM by inducing a different fault condition. If the fault reported changes, this indicates the OCSM is functioning correctly and is not the source of the fault.
- Ignition OFF.
- WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
- Disconnect: OCS Weight Sensor Bolt "A" C3324.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - OCSM.
- DIAGNOSTIC TIP: When viewing DTCs with the OCS weight sensor bolt "A" disconnected, an open sensor circuit fault is normally retrieved.
- Did the on-demand DTC change from B00C0:1A to B00C0:13?
Yes
INSTALL a new seat track assembly with OCS weight sensor bolts. REFER to Seating Seat Track. GO to AD12.
No
GO to AD9.
-------------------------------------------------
AD9 CHECK FOR A SHORT BETWEEN OCS WEIGHT SENSOR BOLT "A" CIRCUITS AND GROUND
- Ignition OFF.
- WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
- Disconnect: OCSM C3159.
- Measure the resistance between OCS weight sensor bolt "A":
- C3324-3, circuit VR211 (WH/BN), harness side and ground.
- C3324-3, circuit VR211 (WH/BN), harness side and C3324-2, circuit RR140 (GN/OG), harness side.
- Are the resistances greater than 10,000 ohms?
Yes
GO to AD10.
No
REPAIR the affected circuits.
Refer to Wiring Diagram Set 5 for schematic and connector information. Diagrams By Number
GO to AD12.
-------------------------------------------------
AD10 CONFIRM THE OCSM FAULT
NOTE: Make sure all restraint system components and the RCM electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.
- Ignition OFF.
- WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
- Prior to reconnecting any previously disconnected SRS component:
- inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
- inspect wire harness for any damage, pinched, cut or pierced wires.
- repair any concerns found.
Refer to Wiring Diagram Set 5, Connector Repair Procedures for schematic and connector information. Diagrams By Number
- Connect: OCSM C3159 (if previously disconnected).
- Connect: OCS Weight Sensor Bolt "A" C3324.
- If previously directed to depower the SRS, repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - OCSM.
- Was the original DTC retrieved on-demand during self-test?
Yes
INSTALL a new OCSM. REFER to Occupant Classification System Module (OCSM) Service and Repair. GO to AD12.
No
In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to AD11.
-------------------------------------------------
AD11 CHECK FOR AN INTERMITTENT FAULT
- Ignition OFF.
- WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
- Disconnect: OCS Weight Sensor Bolt "A" C3324.
- inspect connector(s) (including any in-line connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
- inspect wire harness for any damage, pinched, cut or pierced wires.
- repair any concerns found.
Refer to Wiring Diagram Set 5, Connector Repair Procedures for schematic and connector information. Diagrams By Number
- Connect: All Previously Disconnected Component(s)/Connector(s).
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - OCSM.
- Was DTC B00C0:12, B00C0:13 or B00C0:1A retrieved on-demand during self-test?
Yes
This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test.
For DTC B00C0:12, GO to AD3.
For DTC B00C0:13, GO to AD5.
For DTC B00C0:1A, GO to AD8.
No
CHECK for causes of the intermittent fault. ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition key frequently. ACTIVATE other systems in the same wire harness. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test.
Refer to Wiring Diagram Set 5, Connector Repair Procedures for schematic and connector information. Diagrams By Number
GO to AD12.
-------------------------------------------------
AD12 CHECK FOR ADDITIONAL SRS DTCs
- Ignition OFF.
- WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
- Reconnect all SRS components (if previously disconnected).
- If previously directed to depower the SRS, repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - Restraints.
- NOTE: When selecting Restraints from the Self Test menu, DTCs are retrieved from the RCM and OCSM.
- Are any RCM and/or OCSM DTCs retrieved on-demand during self-test?
Yes
Do not clear any DTCs until all DTCs have been resolved. GO to the DTC Charts for pinpoint test direction. Diagnostic Trouble Code Tests and Associated Procedures
No
CLEAR all RCM and OCSM CMDTCs. PROVE OUT the SRS. The repair is complete. RETURN the vehicle to the customer.
-------------------------------------------------