Installation

SUSPENSION: REAR NO. 1 SUSPENSION ARM (for 4WD): INSTALLATION

INSTALLATION

1. INSTALL REAR SUSPENSION ARM ASSEMBLY NO.1 LH





(a) Install the rear suspension arm assembly No. 1 with the bolt and nut, and temporarily tighten the bolt.
HINT: Ensure that the paint mark faces to the rear.





(b) Set the rear suspension arm assembly No. 1 in the illustration, and fully tighten the bolt.
Torque: 80 Nm (816 kgf-cm, 59ft-lbf)
2. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY





(a) Raise the rear suspension member with a jack.
(b) Install the rear suspension member with the 4 nuts, 2 bolts and 2 retainers.
Front side - Torque: 115 Nm (1,173 kgf-cm, 85ft-lbf)
Rear side - Torque: 181 Nm (1,846 kgf-cm, 134ft-lbf)
3. INSTALL REAR DRIVE SHAFT ASSEMBLY LH
4. INSTALL REAR DRIVE SHAFT ASSEMBLY RH
HINT: Install the RH side using the same procedures as for the LH side.

5. INSTALL SPEED SENSOR REAR LH
6. INSTALL SPEED SENSOR REAR RH
HINT: Install the RH side using the same procedures as for the LH side.

7. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSEMBLY NO.1 LH





(a) Install the rear suspension arm assembly No. 1 (out side) to the rear axle carrier, and temporarily tighten the bolt.
NOTICE:
When installing the bolt, tighten the bolt temporarily with the nut fixed.

8. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSEMBLY NO.1 RH
HINT: Temporarily tighten the RH side using the same procedures as for the LH side.

9. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSEMBLY NO.2 LH





(a) Install the rear suspension arm No. 2 (out side) to the rear axle carrier, and temporarily tighten the bolt.
NOTICE:
When installing the bolt, tighten the bolt temporarily with the nut fixed.

10. TEMPORARILY TIGHTEN REAR SUSPENSION ARM ASSEMBLY NO.2 RH
HINT: Temporarily tighten the RH side using the same procedures as for the LH side.

11. TEMPORARILY TIGHTEN STRUT ROD ASSEMBLY REAR Installation
12. STABILIZE SUSPENSION Installation
13. FULLY TIGHTEN REAR SUSPENSION ARM ASSEMBLY NO.1 LH





(a) Fully tighten the bolt.
Torque: 112 Nm (1,140 kgf-cm, 83ft-lbf)
14. FULLY TIGHTEN REAR SUSPENSION ARM ASSEMBLY NO.1 RH
HINT: Fully tighten the RH side using the same procedures as for the LH side.

15. FULLY TIGHTEN REAR SUSPENSION ARM ASSEMBLY NO.2 LH





(a) Fully tighten the bolt.
Torque: 112 Nm (1,140 kgf-cm, 83ft-lbf)
(b) Install the height control sensor sub-assembly, and connect the height control sensor wire (w/ height control sensor sub-assembly).
Torque: 5.4 Nm (55 kgf-cm, 48in-lbf)
16. FULLY TIGHTEN REAR SUSPENSION ARM ASSEMBLY NO.2 RH
HINT: Fully tighten the RH side using the same procedures as for the LH side.

17. FULLY TIGHTEN STRUT ROD ASSEMBLY REAR
18. INSTALL REAR WHEEL
Torque: 103 Nm (1,050 kgf-cm, 76ft-lbf)
19. TEMPORARILY TIGHTEN PROPELLER W/CENTER BEARING SHAFT ASSEMBLY
20. FULLY TIGHTEN PROPELLER W/CENTER BEARING SHAFT ASSEMBLY
21. INSTALL EXHAUST PIPE ASSEMBLY
22. CHECK FOR EXHAUST GAS LEAK
23. INSPECT REAR WHEEL ALIGNMENT
24. ADJUST VEHICLE HEIGHT
25. ADJUST HEADLIGHT AIM ONLY Adjustments
26. CHECK ABS SPEED SENSOR SIGNAL