Removal

INTERIOR: ROOF HEADLINING (for Regular Cab): REMOVAL

1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Service Precautions.

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

3. REMOVE FRONT FLOOR FOOTREST Removal

4. REMOVE FRONT DOOR SCUFF PLATE LH

(a) Disengage the 8 claws and clip, and remove the front door scuff plate.

5. REMOVE FRONT DOOR SCUFF PLATE RH

HINT
Follow the same procedures as for the front door scuff plate LH.

6. REMOVE COWL SIDE TRIM BOARD LH

(a) Remove the clip.

(b) Disengage the 2 clips and remove the cowl side trim board.

7. REMOVE COWL SIDE TRIM BOARD RH

HINT
Follow the same procedures as for the cowl side trim board LH.

8. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

(a) Remove the front door opening trim weatherstrip.

9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT
Follow the same procedures as for the front door opening trim weatherstrip LH.

10. REMOVE FRONT PILLAR GARNISH LH

(a) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug.

Text in Illustration

HINT
Follow the same procedures as for the opposite side.

(b) Remove the 2 screws.

(1) Using a clip remover, remove the 3 wire harness clamps.

11. REMOVE FRONT PILLAR GARNISH RH

HINT
Follow the same procedures as for the front pillar garnish LH.

12. REMOVE INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake) Removal

13. REMOVE INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake) Removal

14. REMOVE REAR CONSOLE UPPER PANEL SUB-ASSEMBLY

(a) for Automatic Transmission on Separate Seat Type:

(1) Remove the rear console upper panel sub-assembly Removal.

(b) for Manual Transmission on Separate Seat Type:

(1) Remove the rear console upper panel sub-assembly Removal.

15. REMOVE REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type) Removal

16. REMOVE INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type) Removal

17. REMOVE FRONT CONSOLE BOX

(a) for Automatic Transmission on Separate Seat Type:

(1) Remove the front console box Removal.

(b) for Manual Transmission on Separate Seat Type:

(1) Remove the front console box Removal.

(c) for Automatic Transmission on Bench Seat Type:

(1) Remove the front console box Removal.

(d) for Manual Transmission on Bench Seat Type:

(1) Remove the front console box Removal.

18. REMOVE AIR CONDITIONING CONTROL ASSEMBLY Removal

19. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET Removal

20. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY Disassembly

21. REMOVE INSTRUMENT LOWER PANEL FINISH PANEL Removal

22. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY Removal

23. REMOVE COMBINATION METER ASSEMBLY Removal

24. REMOVE INSTRUMENT CENTER CLUSTER FINISH PANEL SUB-ASSEMBLY Removal

25. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY Removal

26. REMOVE INSTRUMENT LOWER PANEL FINISH PANEL SUB-ASSEMBLY Removal

27. REMOVE INSTRUMENT LOWER PANEL Removal

28. REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY Removal

29. REMOVE INSTRUMENT SIDE PANEL Removal

30. DISCONNECT PASSENGER AIRBAG CONNECTOR Removal

31. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY Removal

32. REMOVE BACK PANEL TRIM COVER

(a) for Separate Seat Type and Bench Seat Type:

HINT
Follow the same procedures as for the opposite side (for Bench Seat Type).

(1) Disengage the 6 claws and remove the back panel trim cover.

(b) for Bench Seat Type:

(1) Disengage the 6 claws and remove the back panel trim cover.

33. REMOVE BACK PANEL UPPER GARNISH

(a) Disengage the 4 claws and 5 clips, and remove the back panel upper garnish.

34. REMOVE JACK ASSEMBLY (for Separate Seat Type)

35. REMOVE BACK PANEL TRIM COVER (for Separate Seat Type)

(a) Remove the 2 clips.

(b) Disengage the 4 claws and remove the back panel trim cover.

36. REMOVE BACK PANEL TRIM (for Separate Seat Type)

(a) Remove the 4 clips and back panel trim.

37. REMOVE QUARTER TRIM LOWER PANEL LH

(a) Disengage the 2 claws and 3 clips, and remove the quarter trim lower panel.

38. REMOVE QUARTER TRIM LOWER PANEL RH

HINT
Follow the same procedures as for the quarter trim lower panel LH.

39. REMOVE QUARTER INSIDE TRIM BOARD LH

(a) for LH Side and Separate Seat Type RH side:

(1) Remove the bolt and the floor anchor of the front seat outer belt.

(b) for Bench Seat Type RH Side:

(1) Remove the bolt and the floor anchor of the front seat outer belt.

(2) Disconnect the belt tension sensor connector.

(3) Remove the wiring harness clamp.

(c) Using a screwdriver with its tip taped in protective tape, disengage the claw and open the cover.

Text in Illustration

(d) Remove the 3 screws.

(e) Disengage the 2 clips and remove the quarter trim board.

40. REMOVE QUARTER INSIDE TRIM BOARD RH

HINT
Follow the same procedures as for the quarter trim board LH.

41. REMOVE ROOM LIGHT ASSEMBLY

(a) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the room light lens.

Text in Illustration

(b) Using a screwdriver with its tip taped in protective tape, disengage the 3 claws.

Text in Illustration

(c) Disconnect the room light connector and remove the room light.

42. REMOVE ASSIST GRIP PLUG

HINT
Follow the same procedures as for the opposite side.

(a) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and open the cover.

Text in Illustration

(b) Remove the screw.

(b) Remove the visor from the visor holder.

44. REMOVE VISOR ASSEMBLY RH

HINT
Follow the same procedures as for the visor assembly LH.

45. REMOVE VISOR HOLDER

HINT
Follow the same procedures as for the opposite side.

(a) Turn the visor holder 90° counterclockwise and remove it.

46. REMOVE COAT HOOK

HINT
Follow the same procedures as for the opposite side.

(a) Turn the coat hook 90° counterclockwise and remove it.

47. REMOVE ROOF HEADLINING ASSEMBLY

(a) Disconnect the 3 roof wire connectors.

(b) Using a clip remover, remove the wire harness clamps.

(c) Remove the roof headlining from the vehicle.

48. REMOVE ROOF HEADLINING PAD

(a) Remove the roof headlining pad from the roof headlining.

49. REMOVE ROOF WIRE

(a) Remove the 5 adhesive tapes and roof wire.