A/T Pressure Test

A/T Pressure Test

Special Tools Required

- A/T oil pressure gauge set 07406-0020400 or 07406-0020401
- A/T pressure hose, 2,210 mm 07MAJ-PY4011A
- A/T pressure adapter 07MAJ-PY40120
NOTE:

- Disable the VSA by pressing the VSA OFF button.

- VSA DTC(s) may come on during the test-drive. If VSA DTC(s) come on, clear the DTC(s) with the HDS.

1. Make sure the transmission fluid is filled to the proper level. ATF Level Check

2. Raise the vehicle on a lift, or apply the parking brake, block the rear wheels, and raise the front of the vehicle. Make sure it is securely supported.

3. Allow the front wheels to rotate freely.

4. Remove the splash shield.

5. Connect the HDS to the DLC (A) located under the driver's side of the dashboard.

6. Turn the ignition switch to ON (II), and go to the A/T Data List. Make sure the HDS communicates with the PCM. If it does not, go to the DLC circuit troubleshooting. Testing and Inspection






7. Connect the A/T oil pressure gauge to the line pressure inspection port (A). Do not allow dust or other foreign particles to enter the port while connecting the A/T oil pressure gauge.

8. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).

9. Measure the line pressure at the line pressure inspection port (A) while holding the engine speed at 2,000 rpm with the shift lever in P or N.
NOTE: Higher pressures may be noticed if measurements are taken with the shift lever in any position other than P or N.





10. Turn the engine off, then disconnect the A/T oil pressure gauge from the line pressure inspection port.

11. Install the sealing bolt in the line pressure inspection port with a new sealing washer, and tighten the sealing bolt to 18 N-m (1.8 kgf-m, 13 lbf-ft). Do not reuse the old sealing washer.






12. Connect the A/T oil pressure gauge to the 1st clutch pressure inspection port (B).






13. Remove the intake air duct, Service and Repair and connect the A/T oil pressure gauge to the 2nd clutch pressure inspection port (C). Then temporarily install the intake air duct.

14. Start the engine, and shift to S.

15. Shift to 1st gear by pressing the paddle shifter - (downshift switch) if needed, and measure the 1st clutch pressure at the 1st clutch pressure inspection port (B) while holding the engine speed at 2,000 rpm.

16. Upshift to 2nd gear by pressing the paddle shifter + (upshift switch), and measure the 2nd clutch pressure at the 2nd clutch pressure inspection port (C) while holding the engine speed at 2,000 rpm.





17. Turn the engine off, remove the air intake duct, then disconnect the A/T oil pressure gauge from the 1st and 2nd clutch pressure inspection ports.

18. Install the sealing bolts in the 1st and 2nd clutch pressure inspection ports with new sealing washers, and tighten the sealing bolts to 18 N-m (1.8 kgf-m, 13 lbf-ft). Do not reuse the old sealing washers.

19. Install the intake air duct. Service and Repair






20. Connect the A/T oil pressure gauge to the 3rd clutch pressure inspection port (D) and the 5th clutch pressure inspection port (F).






21. Connect the A/T oil pressure gauge to the 4th clutch pressure inspection port (E).

22. Start the engine, and shift to S.

23. Upshift to 3rd gear by pressing the paddle shifter + (upshift switch), and measure the 3rd clutch pressure at the 3rd clutch pressure inspection port (D) while holding the engine speed at 2,000 rpm.

24. Upshift to 4th gear by pressing the paddle shifter + (upshift switch), and measure the 4th clutch pressure at the 4th clutch pressure inspection port (E) while holding the engine speed at 2,000 rpm.

25. Upshift to 5th gear by pressing the paddle shifter + (upshift switch), and measure the 5th clutch pressure at the 5th clutch pressure inspection port (F) while holding the engine speed at 2,000 rpm.





26. Bring the engine back to an idle, then apply the brake pedal to stop the wheels from rotating.

27. Shift to R, then release the brake pedal. Measure the 4th clutch pressure at the 4th clutch pressure inspection port (E) while holding the engine speed at 2,000 rpm.





28. Turn the engine off, then disconnect the A/T oil pressure gauge from the 3rd, 4th, and 5th clutch pressure inspection ports.

29. Install the sealing bolts in the 3rd, 4th, and 5th clutch pressure inspection ports with new sealing washers, and tighten the sealing bolts to 18 N-m (1.8 kgf-m, 13 lbf-ft). Do not reuse the old sealing washers.

30. If any of the pressures are out of the service limit, refer to the problems and probable causes listed in the table.





31. Install the splash shield.

32. Check the ATF level. ATF Level Check