Hydraulic Control Assembly Overview
Hydraulic Control Assembly Overview
1 ATF drain plug, 40 Nm
• Hex head socket 5 mm
2 Oil seal
• Replace
3 Bolt, 10 Nm
• Tighten diagonally in stages
4 Oil Pan
• Removing and installing, refer to => [ Oil Pan ] 01V,01VA Transmission
5 Gasket
• Replace
6 Oil Strainer
• Removing and installing, refer to => [ Oil Strainer ] 01V,01VA Transmission
7 Bolt, 8 Nm
• For mounting valve body:
M6 x 30 mm (qty. 1)
M6 x 60 mm (qty. 16)
• Pay attention to the tightening sequence.
8 Valve Body
• For removing and installing, refer to => Automatic Transmission/Transaxle Automatic Transmission/Transaxle
• Allocation according to transmission code letters
9 Bolt, 8 Nm
10 Bracket
• For wiring harness
• Hook in wiring harness
• Fastened with bolts for valve body
11 Bolt, 6 Nm
12 Transmission Output Speed (RPM) Sensor (G195 )
• For removing and installing, refer to => Automatic Transmission/Transaxle Automatic Transmission/Transaxle
13 Spacer sleeve
• Height: 8 mm
14 Inner oil line
• Replace
• For removing and installing, refer to => Automatic Transmission/Transaxle Automatic Transmission/Transaxle
15 O-ring
• Replace
16 Speedometer Vehicle Speed Sensor (VSS) (G22)
• Not installed on all versions. On transmission without a Speedometer Vehicle Speed Sensor (VSS) (G22), the speed signal from the ABS/ESP control module is transmitted to the appropriate control module via the CAN-Bus.
• transmission with Speedometer Vehicle Speed Sensor (VSS) (G22), refer to => [ Transmission, All Wheel Drive, Code Letters, Assembly Allocation, Gear Ratios, Equipment ] Transmission, All Wheel Drive, Code Letters, Assembly Allocation, Gear Ratios, Equipment
• Removing and installing => [ Speedometer Vehicle Speed Sensor ] 01V,01VA Transmission
17 O-ring
• Replace
• Coat with ATF to insert
18 Multi-Function Transmission Range Switch (F125 )
• Removing and installing, refer to => [ Multi-Function Transmission Range Switch ] Multi-Function Transmission Range Switch
• Selector Shaft Seal, Removing and Installing, refer to => [ Selector Shaft Seal ] Selector Shaft Seal.
19 Bolt, 8 Nm
20 O-ring
• Replace
21 Retaining clip
22 Wiring harness in transmission
• Transmission fluid temperature sensor (G93) integrated in the wiring harness
• For removing and installing, refer to => Automatic Transmission/Transaxle Automatic Transmission/Transaxle
• Disengage from bracket => [ (Item 10) Bracket ]
• Installation position of wiring harness connectors: Flat spot of rear collar faces toward oil pan; tabs on collar are horizontal.
23 Bolt, 9 Nm
24 Transmission Input Speed (RPM) Sensor (G182)
• For removing and installing, refer to => Automatic Transmission/Transaxle Automatic Transmission/Transaxle
25 Connector
• Is connected to wiring harness in transmission
• Must be disconnected before removing the valve body
26 Bolt, 6 Nm
27 Bracket
• For solenoid
28 Solenoid Valve 4 (N91)
• With an O-ring
• For removing and installing, refer to => Automatic Transmission/Transaxle Automatic Transmission/Transaxle
29 Solenoid Valve 3 (N90)
• Without an O-ring
• Removing and installing, refer to => [ Oil Pan ] 01V,01VA Transmission
30 Solenoid Valve 2 (N89)
• Without an O-ring
• Removing and installing, refer to => [ Oil Pan ] 01V,01VA Transmission
31 Bolt, 6 Nm
32 Bracket
• For solenoid valves
33 Solenoid Valve 6 (N93)
• With an O-ring
• Removing and installing, refer to => [ Oil Pan ] 01V,01VA Transmission
34 Solenoid Valve 7 (N94)
• With an O-ring
• Removing and installing, refer to => [ Oil Pan ] 01V,01VA Transmission
35 Solenoid Valve 5 (N92)
• With an O-ring
• Removing and installing, refer to => [ Oil Pan ] 01V,01VA Transmission
36 Solenoid Valve 1 (N88)
• Without an O-ring
• Removing and installing, refer to => [ Oil Pan ] 01V,01VA Transmission and removing park locking mechanism guide plate
• When installing, do not tighten bolts for guide plate (23 Nm) in selector lever position "P".
37 Bolt, 6 Nm
38 Magnet
• Qty. 4, in depressions of oil pan
39 O-ring
• Replace
40 ATF inspection plug, 80 Nm
• Hex head socket 17 mm