Oil Pan, Strainer, and Valve Body Assembly Overview
Oil Pan, Strainer, and Valve Body Assembly Overview
1 Drain plug - 40 Nm
• With seal
• Always replace
• 5 mm socket-head bolt
• Remove to drain ATF => [ Remove ATF drain plug (arrow) and drain
ATF. ] 01VA Transmission
2 Bolt - 10 Nm
• Tighten bolts for oil pan in several stages in diagonal sequence
3 Oil pan
• Removing and installing, refer to => [ Oil Pan ] 01VA Transmission
4 Gasket
• Always replace
5 Oil strainer
• Removing and installing, refer to => [ Oil Strainer ] 01VA Transmission
6 Bolt - 8 Nm
• For mounting valve body: 16 bolts M6 x 60
• Observe tightening sequence => [ Then tighten valve body bolts from inside
out to final tension. ] Valve Body
7 Valve body
• Removing and installing, refer to => [ Valve Body ] Valve Body
• Allocation according to transmission code letters
8 Bolt - 8 Nm
9 Bracket
• For wiring harness
• Hook in wiring harness
• Mounted with valve body bolts
10 Bolt - 6 Nm
11 Transmission Vehicle Speed Sensor (VSS) (G38 ) (also designated as Transmission Output Speed (RPM) Sensor (G195))
• Removing and installing, refer to => [ Transmission Vehicle Speed Sensor ] Transmission Vehicle Speed Sensor
12 Spacer sleeve
• Height: 8 mm
13 Inner oil line
• Always replace
• Removing and installing, refer to => [ Oil Line ] Oil Line
14 O-ring
• Always replace
15 Speedometer Vehicle Speed Sensor (VSS) (G22)
• Removing and installing, refer to => [ Speedometer Vehicle Speed Sensor ] Speedometer Vehicle Speed Sensor
16 O-ring
• Always replace
• Coat with gear oil and insert
17 Multi-Function Transmission Range (TR) Switch ( F125)
• Removing and installing, refer to => [ Multi-Function Transmission Range Switch ] Multi-Function Transmission Range Switch
• Replacing shift rod sealing ring, refer to => [ Shift Rod Seal ] Shift Rod Seal
18 Bolt - 8 Nm
19 O-ring
• Always replace
• Coat with ATF and insert
20 Locking clamp
• Always replace
21 Wiring harness in transmission
• Always replace, refer to => [ Wiring Harness ] Service and Repair
• Transmission Fluid Temperature Sensor (G93) is integrated into the wiring harness
• Remove and install valve body to replace, refer to => [ Valve Body ] Valve Body
• Unhook from bracket for wiring harness, item 10
• Installation position wiring harness connector: Flat part of rear collar points toward oil pan, the tabs at collar are horizontal
22 Bolt - 9 Nm
23 Sensor for transmission RPM (G182)
• Removing and installing, refer to => [ Transmission Input Speed Sensor ] Transmission Input Speed Sensor
24 Connector
• Is connected at wiring harness in transmission
• Must be disconnected before removing the valve body
25 Bolt - 6 Nm
26 Bracket
• For solenoid valve
27 Pressure Control Valve 1 for Auto. Transmission (N215)
• With O-ring
• Remove and install valve body to replace, refer to => [ Valve Body ] Valve Body
28 Solenoid valve 3 (N90)
• Without O-ring
• Remove and install oil pan to replace, refer to => [ Oil Pan ] 01VA Transmission
29 Solenoid valve 2 (N89)
• Without O-ring
• Remove and install oil pan to replace, refer to => [ Oil Pan ] 01VA Transmission
30 Bolt - 6 Nm
31 Bracket
• For solenoid valves
32 Pressure Control Valve 3 for Auto. Transmission (N217)
• With O-ring
• Remove and install oil pan to replace, refer to => [ Oil Pan ] 01VA Transmission
33 Pressure Control Valve 4 for Auto. Transmission (N218)
• With O-ring
• Remove and install oil pan to replace, refer to => [ Oil Pan ] 01VA Transmission
34 Pressure Control Valve 2 for Auto. Transmission (N216)
• With O-ring
• Remove and install oil pan to replace, refer to => [ Oil Pan ] 01VA Transmission
35 Solenoid valve 1 (N88)
• Without O-ring
• Remove and install oil pan to replace, refer to => [ Oil Pan ] 01VA Transmission and unbolt guide plate for park locking mechanism
• When installing, do not tighten bolts for guide plate (23 Nm) in selector lever position "P".
36 Bolt - 6 Nm
37 Magnet
• 4 pieces in the oil pan recesses
• Clean after every removal of oil pan
• Ensure full surface contact in oil pan
38 O-ring
• Always replace
39 ATF check plug - 80 Nm
• 17 mm socket-head bolt