P0132

Circuit Description
The PCM supplies a bias voltage of about 450mV between the HO2S signal and low circuits. When measured with a 10 megohm digital voltmeter, this may display as low as 320mV. The oxygen sensor varies the voltage within a range of about 1000mV when the exhaust is rich, down through about 1OmV when exhaust is lean. The PCM constantly monitors the HO2S signal during closed loop operation and compensates for a rich or lean condition by decreasing or increasing injector pulse width as necessary. If the HO2S 1 voltage remains excessively high for an extended period of time, DTC P0132 will be set.

Conditions for Running the DTC
^ No active TP sensor, EVAP system, misfire, IAT sensor, MAP sensor, fuel trim, fuel injector circuit, EGR Pintle Position, ECT sensor, CKP sensor, or MAF sensor DTC present.
^ System voltage is greater than 9 volts.
^ Closed loop commanded air/fuel ratio is between 14.5 and 14.8.
^ Throttle angle is between 3% and 40%.

Conditions for Setting the DTC
^ HO2S 1 signal voltage remains above 975 mV during normal closed loop operation.
^ HO2S 1 signal voltage remains above 200 mV during deceleration fuel mode operation.
^ Either condition for up to 60 seconds.

Action Taken When the DTC Sets
^ The PCM will illuminate the MIL during the second consecutive trip in which the diagnostic test has been run and failed.
^ The PCM will store conditions which were present when the DTC set as Freeze Frame and Fail Records data.

Conditions for Clearing the MIL/DTC
^ The PCM will turn the MIL OFF during the third consecutive trip in which the diagnostic has been run and passed.
^ The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
^ The DTC can be cleared by using a scan tool.

Diagnostic Aids
Check the following items:
^ Fuel Pressure.
The system will go rich if pressure is too high. The PCM can compensate for some increase. However, if fuel pressure is too high, a DTC P0132 may be set. Refer to Fuel System Pressure Test (VIN 1). Fuel System Pressure Test
^ Fuel injector(s):
Refer to Fuel lnj Coil Test - ECT Between 10-35 Degrees C or Fuel lnj Coil Test - ECT Outside 10-35 Degrees C. Component Tests and General Diagnostics
^ Check the EVAP Canister for fuel saturation. If the EVAP Canister is full of fuel, check the canister control and hoses. Refer to EVAP Control System Diagnosis. Component Tests and General Diagnostics
^ Mass Air Flow Sensor.
Disconnect the MAF sensor and see if the rich condition is corrected. If so, replace the MAF sensor.
^ Fuel Pressure Regulator:
Check for a leaking fuel pressure regulator diaphragm by checking vacuum line to regulator for the presence of fuel. If a problem is found, replace the fuel pressure regulator.
^ TP Sensor:
An intermittent TP sensor output will cause the system to go rich due to a false indication of the engine accelerating. Throttle Angle displayed on a scan tool should increase steadily from 0% to 100% when opening the throttle. If not, check the TP sensor for loose mounting screws. If the TP mounting screws are OK, replace the TP sensor.
^ Shorted Heated Oxygen Sensor (HO2S). If the HO2S is internally shorted the HO2S voltage displayed on the scan tool will be over 1 volt. Disconnect the affected HO2S and jumper the HO2S low circuit to ground with the key ON, engine not running. If the displayed HO2S voltage changes from over 1000 mV to around 450 mV, replace the HO2S. Silicon contamination of the HO2S can also cause a high HO2S voltage to be indicated. This condition is indicated by a powdery white deposit on the portion of the HO2S exposed to the exhaust stream. If contamination is noticed, replace the affected HO2S. Refer to HO2S Replacement - Sensor 1.
^ Open HO2S Signal or Low Circuit or Malfunctioning HO2S.
A poor connection or open in the HO2S signal or low circuit can cause the DTC to set during deceleration fuel mode. An HO2S which is malfunctioning and not allowing a full voltage swing between the rich and lean thresholds can also cause this condition. Operate the vehicle while monitoring the HO2S voltage with a scan tool. If the HO2S voltage is limited within a range between 300 mV to 600 mV, check the HO2S signal and low circuit wiring and associated terminal connections.
^ If the wiring and connections are OK, replace the affected HO2S. Refer to HO2S Replacement - Sensor 1.

Test Description
Number(s) below refer to step numbers on the Diagnostic Table.
3. DTC P0132 failing during deceleration fuel mode operation (vehicle speed above 40 km/h (25 mph), TP angle less than 3%) may indicate a condition described in Diagnostic Aids. If the DTC P0132 test passes while the Fail Records conditions are being duplicated, an intermittent condition is indicated. Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.
8. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed.