Accumulator Assembly, Spacer Plate, and Gaskets

Accumulator Assembly, Spacer Plate, and Gaskets
^ Tools Required
- J 25025-B Pump and Valve Body Alignment Pin Set
- J 36850 Transjel Lubricant

Removal Procedure





1. Remove the transmission filter.

Important: The 1-2 accumulator can be removed without removing the valve body.

2. Remove the valve body. Refer to Valve Body and Pressure Switch Replacement.
3. Remove the accumulator cover bolts.
4. Remove the 1-2 accumulator cover.





5. Disassemble the 1-2 accumulator.
5.1. Blow compressed air into the 1-2 accumulator cover, as shown, in order to remove the 1-2 accumulator piston.
5.2. Remove the 1-2 accumulator inner and outer springs.
6. Inspect the 1-2 accumulator inner and outer springs for cracks.





7. Remove the 1-2 accumulator piston seal (1) from the 1-2 accumulator piston.
8. Inspect the 1-2 accumulator piston for the following defects:
^ Porosity
^ Cracks
^ Scoring
^ Nicks and scratches





9. Inspect the 1-2 accumulator cover for the following defects:
^ Porosity
^ Cracks
^ Scoring
^ Nicks and scratches





10. Remove the spacer plate support bolts.

Important: Use care not to drop the following items that will be removed along with the spacer plate:
^ The number 1 checkball
^ The 3-4 accumulator spring
^ The 3-4 accumulator pin

11. Remove the spacer plate support.





12. Remove the spacer plate to valve body gasket, the spacer plate and the spacer plate to transmission case gasket.





13. Remove the 3-4 accumulator piston (2).
14. Inspect the 3-4 accumulator spring for cracks.





15. Remove the 3-4 accumulator piston seal (1) from the 3-4 accumulator piston.
16. Inspect the 3-4 accumulator piston for the following defects:
^ Porosity
^ Cracks
^ Scoring
^ Nicks and scratches

Installation Procedure





1. Install a new 3-4 accumulator piston seal (1) to the 3-4 accumulator piston.





2. Install the 3-4 accumulator pin (1) into the transmission case and retain the pin with J 36850.





3. Install the 3-4 accumulator piston (2) onto the pin (1) in the transmission case.
Ensure that the 3-4 accumulator piston legs face away from the transmission case.





4. install the J25025-B (2, 3) to the transmission case.





5. Install the spacer plate to transmission case gasket and the spacer plate to valve body gasket to the spacer plate; use J 36850 in order to retain the gaskets to the spacer plate.
^ The case gasket is identified by a C.
Be sure to place the case gasket on the transmission case side of the spacer plate.
^ The valve body gasket is identified by a V.
Be sure to place the valve body gasket on the valve body side of the spacer plate.
6. Ensure that the solenoid screens (1, 2) are in place on the spacer plate.
7. Place the checkball (3) on the spacer plate in the location shown.
8. Place the 3-4 accumulator spring (4) on the spacer plate.
9. Install the spacer plate and related components to the transmission.





Notice: Refer to Fastener Notice in Service Precautions.

10. Install the spacer plate support and the spacer plate support bolts.
^ Tighten the bolts to 11 Nm (97 inch lbs.).





11. After installing the spacer plate support (2), look through the hole in the spacer plate to ensure that the checkball (1) has remained in the proper location.





12. Install a new 1-2 accumulator piston seal (1) to the 1-2 accumulator piston.





13. Install the 1-2 accumulator inner and outer springs to the 1-2 accumulator cover.
14. Install the 1-2 accumulator piston onto the pin in the 1-2 accumulator cover.
Ensure that the piston legs face the accumulator cover.





15. Install the 1-2 accumulator cover and the accumulator cover bolts.
^ Tighten the bolts to 11 Nm (97 inch lbs.).
16. Remove the J 25025-B from the transmission case.
17. Install the valve body. Refer to Valve Body and Pressure Switch Replacement.
18. Install the transmission filter. Refer to Automatic Transmission Fluid/Filter Replacement.