B0074

DTC B0074

DTC DESCRIPTORS

DTC B0074 03
Passenger Occupant Classification Sensor Circuit Voltage Below Threshold

DTC B0074 07
Passenger Occupant Classification Circuit Voltage Above Threshold

DTC B0074 08
Passenger Occupant Classification Circuit Signal Invalid

DIAGNOSTIC FAULT INFORMATION

IMPORTANT: Always perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Testing and Inspection

CIRCUIT/SYSTEM DESCRIPTION
The passenger presence system (PPS) uses a silicone filled sensor pad located underneath the passenger seat foam cushion and is connected by a hose clamp to a pressure sensor. The weight of the occupant sitting in the front passenger seat is measured as a pressure change within the bladder by the pressure sensor. The pressure sensor is a 3-wire sensor consisting of a power, ground, and signal circuit. The PPS continually monitors itself and if a fault in this circuit occurs, a DTC will set. When the SDM detects this DTC within the PPS, it will notify the customer of the enable/disable status by turning ON the OFF indicator on the PASSENGER AIR BAG ON/OFF indicators. Then the PPS will communicate to the sensing and diagnostic module (SDM) through serial data communications that a PPS fault is present. The SDM will then suppress the deployment of the instrument panel (I/P) module and then turn the AIR BAG indicator ON.

CONDITIONS FOR RUNNING THE DTC
Ignition voltage is between 9-16 volts.

CONDITIONS FOR SETTING THE DTC
- The PPS detects the voltage at the PPS sensor signal is less than 0.05 volt or greater than 4.5 volts for 500 milliseconds.
- The PPS detects the voltage at the PPS sensor 5-volt reference is less than 4.5 volts or greater than 9.1 volts for 500 milliseconds.
- The PPS detects the amperage at the PPS sensor low reference is 25 ma or greater for 500 milliseconds.

ACTION TAKEN WHEN THE DTC SETS
- The PPS will set a DTC, and then communicate with the SDM via serial data communications.
- The SDM disables the I/P module deployment loop.
- The PPS will turn ON the passenger air bag status OFF indicator.
- The SDM commands ON the AIR BAG warning lamp via serial data communications.

CIRCUIT/SYSTEM TESTING
1. Ignition OFF, inspect the component and harness sides of the connector for the PPS pressure sensor. Verify there is no damage or corrosion is found.

IMPORTANT: When removing connectors, inspect for damage or corrosion. Damage or corrosion in the following requires repair or replacement of the affected component/connector:
- The PPS pressure sensor
- The PPS module
- The PPS pressure sensor wiring harness connector
- The PPS module wiring harness connector

2. Disconnect the PPS module connector.
3. Test the PPS sensor signal circuit for a short to ground, a high resistance, or an open. Verify that a short to ground, a high resistance, or an open does not exist.
- If any of the above conditions are found, make the appropriate repair.
4. Test the PPS sensor low reference circuit for a short to ground, a short to voltage, a high resistance, or an open. Verify that a short to ground, a short to voltage, a high resistance, or an open does not exist.
- If any of the above conditions are found, make the appropriate repair.
5. Test the PPS sensor 5-volt reference circuit for a short to ground, a short to voltage, a high resistance, or an open. Verify that a short to ground, a short to voltage, a high resistance, or an open does not exist.
- If any of the above conditions are found, make the appropriate repair.
6. Ignition ON, engine OFF test the PPS sensor signal circuit with a DMM. Measure the voltage of the PPS sensor circuit harness side and ground. The voltage should read 0.05-4.5 volts.
- If the voltage is more than 5 volts, test the PPS sensor signal circuit for a short to voltage. If the circuit tests good, replace the PPS.
7. Reconnect all PPS components. Use the scan tool to clear all PPS DTCs. Rezero the PPS. Refer to Passenger Presence System Rezeroing Procedure. Verify DTC B0074 does not exist. Programming and Relearning
- If DTC B0074 reset, replace the PPS.

REPAIR INSTRUCTIONS

IMPORTANT: Always perform the Diagnostic Repair Verification after completing the diagnostic procedure. Verification Tests

Control Module References for PPS replacement, setup, and programming.