Steering - Noise At Full Lock
Number:92-252A-3C
Section:
3C
Date:
SEPT. 1992
Corporate Bulletin No.:
863301R
ASE No.:
A4
Subject:
NOISE AT FULL STEERING LOCK
Model and Year:
1988 AND 1992 C TRUCKS
THIS BULLETIN CANCELS AND SUPERSEDES DEALER SERVICE BULLETIN NO. 92-252-3C, DATED AUGUST, 1992. VIN BREAKPOINTS HAVE BEEN CORRECTED. ALL COPIES OF 92-252-3C SHOULD BE DISCARDED.
Some owners of 1988 and 1992 C trucks may experience a condition where the brake rotor comes in contact with the lower control arm. This occurs only when the steering wheel is turned to the full lock position and most often on left hand turns. The interference between the lower control arm and brake rotor will cause a screeching noise as metal rubs metal. A gouge on the inner brake rotor is evidence that an interference condition does exist.
On vehicles with this condition, the nose area of the lower control arm should be ground away to provide additional clearance. If a gouge is found on the inside of the brake rotor, then replacement of the rotor will be necessary.
Vehicles Involved:
In addition to the 1988 C1 and C2 models, certain 1992 C1 and C2 models built within the following VIN breakpoints are involved.
Plant Beginning Ending
Pontiac East NE177646 NE190038
Oshawa CEC19H6N1206608 2CCEC19K7N1221548
Fort Wayne 1GBDC14K7NZ189800 1GCEC14K7NZ194690
Janesville None
Service Procedure
1. Inspect brake rotor for signs of contact with the lower control arm.
2. If a gouge is found, replacement of the brake rotor will be necessary.
3. Siphon 2/3 of the brake fluid from the master cylinder.
4. Remove the wheel and tire assembly
5. Remove the brake caliper from the brake rotor. Suspend the caliper assembly with a wire hook away from the work area.
6. Remove wheel bearing cap and nut from the spindle.
7. Remove the brake rotor and discard if a gouge is found. Care should be used so that the outer bearing and spindle threads are not damaged. Save the bearings.
8. Remove the brake splash shield and gasket.
9. Mark the center nose portion of the lower control arm. Place another mark 2 inches on either side of center (Figure No.1).
10. Using a die grinder or equivalent, take care not to remove more than 2 mm (.08 inches) of metal from the control arm nose to obtain clearance between the control arm and brake rotor.
11. Inspect the outer nose of the control arm for the flange thickness. The thickness should be 10 mm - 14 mm (.39 - .55 inches). (Figure No. 2)
12. If the flange thickness is greater than 14 mm (.55 inches), use a die grinder or equivalent to remove excessive metal from the bottom to obtain the proper thickness.
13. Clean the unfinished metal, then paint black.
14. Reinstall gasket and splash shield. Torque bolts to 16 N-m (12 lb.ft.).
15. Install inner bearing to the brake rotor. Apply an additional amount of an approved high temperature front wheel bearing grease outboard of the inner bearing.
16. Install a new wheel seal using a flat plate to press the seal down flush with the hub. Apply a film of wheel bearing grease to lubricate the seal.
17. Install brake rotor to the spindle.
18. Apply grease to the outboard side of the outer bearing. Reinstall outer bearing to the brake rotor.
19. Reinstall nut and washer to the spindle. Tighten nut to 16 N-m (12 lb.ft) while turning the brake rotor assembly forward by hand. This will seat the bearings. Adjust the nut to a "just loose" position by hand, then back the nut off until the hole in the spindle aligns with a slot in the nut. Do not back the nut off more than 1/2 flat. Install new cotter pin.
20. Reinstall cap to the brake rotor.
21. Check for control arm to rotor clearance in the straight ahead position and in a full right and left hand turn.
22. Reinstall brake caliper Torque caliper mounting bolts to 51 N-m (38 lb.ft).
23. Reinstall wheel and tire assembly. Torque nuts to 160 N-m (120 lb.ft).
24. Refill the master cylinder with Delco Supreme II fluid, Part Number 1052535, or Dot 3, and bleed brake system if required.
Labor time to perform this procedure is:
.7 hr -One Side Labor 0p T 7405
1.1 hrs - Both Sides Labor 0p T 7410