P0137 or P0157 (w/ Delphi HO2S)

CIRCUIT DESCRIPTION
This diagnostic applies only to vehicles built with Delphi heated oxygen sensors. To identify the heated oxygen sensor refer to Delphi/Denso Sensor in Computers and Control Systems Component Views.

The Powertrain Control Module (PCM) supplies a voltage of about 450 mV between the Heated Oxygen Sensor (HO2S) high and low signal circuits. The oxygen sensor varies the voltage over a range from about 1,000 mV when the exhaust is rich, down through about 10 mV when the exhaust is lean.

The PCM monitors and stores the HO2S voltage information. The PCM evaluates the HO2S voltage samples in order to determine the amount of time the HO2S voltage was out of range. The PCM compares the stored HO2S voltage samples taken within each sample period and determines if the majority of the samples are out of the operating range.

The PCM monitors the HO2S voltage for being fixed below a predetermined voltage. If the PCM detects the voltage is below a predetermined voltage, a Diagnostic Trouble Code (DTC) sets.

CONDITIONS FOR RUNNING THE DTC
^ DTC P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0117, P0118, P0121, P0122, P0123, P0200, P0300, P0401, P0404, P0405, P0410, P0440, P0442, P0446, P0452, P0453, P1120, P1125, P1220, P1221, P1258, P1404, P1415, P1416, P1514, P1515, P1516, P1517, or P1518 are not set.
^ The air fuel ratio is between 14.5:1 and 14.7:1.
^ Vehicles without Throttle-actuated Control (TAC), the Throttle Position (TP) is between 3-70 percent.
^ Vehicles with Throttle-actuated Control (TAC) the Throttle Position (TP) indicated angle is between 3-70 percent more than the value observed at idle.
^ The loop status is closed.
^ The ignition 1 signal is between 9-18 volts.
^ The fuel tank level remaining is more than 10 percent.
^ Intrusive tests are not in progress.
^ The scan tool output controls are not active.

CONDITIONS FOR SETTING THE DTC
The HO2S voltage is less than 80 mV for 400 seconds.

ACTION TAKEN WHEN THE DTC SETS
^ The control module illuminates the Malfunction Indicator Lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
^ The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

CONDITIONS FOR CLEARING THE MIL/DTC
^ The control module turns OFF the Malfunction Indicator Lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
^ A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
^ A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
^ Use a scan tool in order to clear the MIL and the DTC.

DIAGNOSTIC AIDS

IMPORTANT: Remove any debris from the PCM connector surfaces before servicing the PCM. Inspect the PCM connector gaskets when diagnosing or replacing the PCM. Ensure that the gaskets are installed correctly. The gaskets prevent water intrusion into the PCM.

^ HO2S wire-Sensor pigtail may be in contact with the exhaust manifold or the exhaust system.
^ An oxygen supply inside the HO2S is necessary for proper operation. The HO2S wires provide the supply of oxygen. Inspect the HO2S wires and connections for breaks or contamination. Refer to Heated Oxygen Sensor (HO2S) Wiring Repairs in Diagrams.
^ Check for intermittent ground in the signal wire between the connector and the sensor. Refer to Testing for Intermittent and Poor Connections in Diagrams.
^ Lean injectors-Perform the Injector Balance Test. Refer to Fuel Injector Balance Test with Tech 2 or Fuel Injector Balance Test with Special Tool. Component Tests and General Diagnostics Component Tests and General Diagnostics
^ Fuel contamination-Water near the in-tank fuel pump inlet can be delivered to the injectors. The water causes a lean exhaust and can set a DTC. Refer to Alcohol/Contaminants-in-Fuel Diagnosis. Fuel
^ Fuel pressure-System will be lean if fuel pressure is low. Refer to Fuel System Diagnosis. Component Tests and General Diagnostics
^ Exhaust leaks-An exhaust leak near the HO2S can cause a lean condition. Refer to Exhaust Leakage in Exhaust System.
^ Vacuum or crankcase leaks can cause a lean condition.
^ If the above are OK, the HO2S may be at fault.

For an intermittent condition, Refer to Intermittent Conditions. Intermittent Conditions

TEST DESCRIPTION

Steps 1-6:

Steps 7-13:

The numbers below refer to the step numbers on the diagnostic table.
2. If the voltage is below the specified value the condition is present.
4. Jumpering the HO2S low signal circuit to ground is necessary for the PCM to correctly measure the voltage on the HO2S high signal circuit. If the HO2S voltage is within the specified range, the PCM and HO2S high signal circuit are OK.