B3920
DTC B3920 or B3921
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B3920 01
- Group 1 Seat Motors Common Circuit Short to Battery
DTC B3920 02
- Group 1 Seat Motors Common Circuit Short to Ground
Diagnostic Fault Information
Circuit/System Description
The memory seat module (MSM) controls the seat, recline, lumbar, and adjustable pedal motors via half bridges that are connected to a common power rail internal to the module. The MSM connects all of the motor control circuits to a common reference point whenever they are not in operation. This reference point is biased to approximately 2.5 volts. The MSM checks to see if this reference voltage is shorted to ground or battery before enabling any seat, lumbar, or adjustable pedal motor.
Conditions for Running the DTC
The MSM must be powered.
Conditions for Setting the DTC
B3920 01
The voltage on any power rail 1 motor control circuit exceeds 2.78 volts for 100 ms.
B3920 02
The voltage on any power rail 1 motor control circuit is below 1.47 volts for 100 ms.
Action Taken When the DTC Sets
The MSM will not allow operation of any motor on the power rail for which the DTC was set.
Conditions for Clearing the DTC
* The current DTC clears when the malfunction is no longer present and the power mode changes to OFF then back to ACC or RUN.
* The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred.
Reference Information
Schematic Reference
* Driver Seat Schematics (Driver Seat Schematics)
* Adjustable Pedal Schematics (Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector Views)
Description and Operation
Memory Seats Description and Operation (Memory Seats)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the X1 harness connector at the MSM.
2. Ignition ON, verify that a test lamp does not illuminate between the control circuits listed below and ground:
* Front vertical motor terminal 12
* Front vertical motor terminal 13
* Rear vertical motor terminal 15
* Rear vertical motor terminal 16
* Seat horizontal motor terminal 9
* Seat horizontal motor terminal 10
• If the test lamp illuminates, test the control circuit for a short to voltage.
3. Test for infinite resistance between the control circuits listed below and ground:
* Front vertical motor terminal 12
* Front vertical motor terminal 13
* Rear vertical motor terminal 15
* Rear vertical motor terminal 16
* Seat horizontal motor terminal 9
* Seat horizontal motor terminal 10
• If not the specified value, test the control circuit for a short to ground.
4. Ignition OFF, disconnect the X4 harness connector at the MSM.
5. Ignition ON, verify that a test lamp does not illuminate between the control circuits listed below and ground:
* Lumbar vertical motor terminal 1
* Lumbar vertical motor terminal 2
* Lumbar horizontal motor terminal 12
* Lumbar horizontal motor terminal 13
* Seat recline motor terminal 15
* Seat recline motor terminal 16
* Adjustable pedal actuator terminal 9
* Adjustable pedal actuator terminal 10
• If the test lamp illuminates, test the control circuit for a short to voltage.
6. Test for infinite resistance between the control circuits listed below and ground:
* Lumbar vertical motor terminal 1
* Lumbar vertical motor terminal 2
* Lumbar horizontal motor terminal 12
* Lumbar horizontal motor terminal 13
* Seat recline motor terminal 15
* Seat recline motor terminal 16
* Adjustable pedal actuator terminal 9
* Adjustable pedal actuator terminal 10
• If not the specified value, test the control circuit for a short to ground.
7. If all circuits test normal, replace the MSM.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Front Seat Adjuster Replacement (Power) (Service and Repair)
* Driver or Passenger Seat Back Cushion Frame Replacement (Driver or Passenger Seat Back Cushion Frame Replacement)
* Driver or Passenger Seat Lumbar Support Replacement (Driver or Passenger Seat Lumbar Support Replacement)
* Brake Pedal Assembly Replacement (Brake Pedal Assembly Replacement)
* Control Module References (Programming and Relearning) for the MSM replacement, programming and setup