Rear Sliding Window Replacement

Rear Sliding Window Replacement

Removal Procedure





Note: The new rear sliding window regulator and cables are serviced as an assembly.

1. Cycle the rear sliding window to the halfway position.
2. Remove the rear lower garnish molding. Refer to Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/A48) (Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/A48))Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/o A48) (Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/o A48))Rear Window Lower Garnish Molding Replacement (Regular Cab) (Rear Window Lower Garnish Molding Replacement (Regular Cab)).

Note: Use a suitable tool to lift upward on the rear sliding window stops (1) to remove.

3. Remove the rear sliding window stops (1).





Note: Use a suitable tool to release the tabs (1) from the rear sliding window pulley (3).

4. Remove the rear sliding window pulley covers (2).




5. Remove the regulator cables (2) from the retainers (1) located across the bottom edge of the window frame.




6. Remove the screw (1) from regulator (2).
7. Remove the regulator (2) from the motor/module.




8. Remove the pulley (1) from the frame.

1. Lift the end of the tabs (2) out of the window frame (3).
2. Turn upward to release the pulley (1) from the frame (3).




9. Remove the cable ends (1) from the window guide (2) at each end of the window.




10. Remove the regulator (1) and cables (2) from the vehicle.




11. Remove the rear sliding window catch screws (1), catch, gasket (2) and nuts (3).
12. Slide the window all the way to the left (driver side).
13. Release the window from the upper frame, by push downward on the window.
14. Remove the rear sliding window (4) from the frame.

Installation Procedure




1. Install the rear sliding window (4) to the frame.
2. Align the window to the upper and lower frame, push down the window and then pull upward locking the window in the frame.
3. Slide the window all the way to the right (passenger side).

Caution: Refer to Fastener Caution (Fastener Caution).

4. Install the rear sliding window catch screws (1), catch, gasket (2) and nuts (3).

Tighten the nuts to 3 Nm (27 lb in).




5. Slide window by hand, back and forth in the window frame to ensure proper operation before installing the regulator to the motor.
6. Install the window to the halfway position.
7. Install the regulator (1) and cables (2) to vehicle.




8. Install the cable ends (1) to the window guide (2) at each end of the window.





Note: When installing the regulator (2) align the gear to the motor drivegear before installing the screw.

9. Install the regulator (2) to the motor/module.
10. Install the screw (1) to the motor/module.

Tighten nuts to 5 Nm (44 lb in).




11. Install the rear sliding window pulley (1).

1. Align the tabs (2) on the pulley (1) with the notch in the frame (3).
2. Turn the pulley downward, locking the pulley into the frame (3).




12. Install the regulator cables (2) to the retainers (1) across the bottom edge of the window frame.




13. Install the rear sliding window pulley covers (2) to the pulley (3), clip the tabs (1) in place.




14. Install the rear sliding window stops (1) until fully seated.
15. Cycle the rear sliding window to the fully closed position.
16. Install the lower garnish molding. Refer to Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/A48) (Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/A48))Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/o A48) (Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/o A48))Rear Window Lower Garnish Molding Replacement (Regular Cab) (Rear Window Lower Garnish Molding Replacement (Regular Cab)).
17. Inspect the rear sliding window for proper operation.
18. Clean the window.