Tahoe/Yukon Hybrid Minus Denali)
DTC B0081 (Tahoe/Yukon Hybrid Minus Denali)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using the diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B0081 0F
- Passenger Presence System Erratic (sets in the SDM)
DTC B0081 3A
- Passenger Presence System Incorrect Component Installed (sets in the SDM)
DTC B0081 4B
- Passenger Presence System Calibration Not Learned (sets in the passenger presence (PPS) module)
DTC B0081 5A
- Passenger Presence System Plausibility Failure (sets in PPS module)
DTC B0081 39
- Passenger Presence System Internal Electronic Failure (sets in SDM)
DTC B0081 71
- Passenger Presence System Invalid Serial Data Received (sets in SDM)
Circuit/System Description
When the ignition is turned ON, the passenger presence system (PPS) and the inflatable restraint sensing and diagnostic module (SDM) performs tests to diagnose critical malfunctions. When the SDM has completed the power-up mode, the SDM will establish communication with the PPS module. The SDM will also request the instrument panel cluster (IPC) to illuminate both of the PASSENGER AIR BAG ON/OFF indicators ON for 5 seconds. If the SDM determines the correct PPS is installed and functioning normally, the SDM will illuminate the passenger air bags ON or OFF indicator based on messages from the PPS. The SDM sends a message to the IPC to illuminate the appropriate PASSENGER AIR BAG ON/OFF indicator.
Conditions for Running the DTC
Ignition voltage is between 9-16 volts.
Conditions for Setting the DTC
All of the following conditions must exist for 5 seconds:
B0081 0F
The SDM sets this DTC if there is a fault present in the PPS module.
B0081 3A
The SDM sets this DTC when the SDM has received a message from the PPS which indicates a mismatch between the SDM and PPS module. There is either an incorrect SDM or PPS module installed on this vehicle.
B0081 4B
The PPS module sets this DTC when the PPS module has not learned the calibrations.
B0081 5A
The PPS module sets this code when the PPS module has lost communications with the SDM.
B0081 39
The SDM sets this DTC when the SDM has received a critical fault message from the PPS module.
B0081 71
The SDM sets this DTC when the SDM has received invalid serial data from the PPS module.
Action Taken When the DTC Sets
* The SDM disables the passenger instrument cluster air bag.
* The PPS module will illuminate the Passenger Airbag On/Off indicator status as OFF.
* When the PPS module sets this DTC, the PPS module communicates with the SDM to turn the AIRBAG indicator on.
* When the SDM sets this DTC, the SDM will turn the AIRBAG indicator on.
* The SDM requests the instrument panel cluster (IPC) to illuminate the AIRBAG indicator.
Conditions for Clearing the DTC
* The condition for setting the DTC no longer exists and there is no activity on the low speed serial data circuits.
* A history DTC will clear once 100 malfunction-free ignition cycles have occurred.
Diagnostic Aids
If either the SDM or PPS module were replaced, verify that the correct replacement part numbers were used for this vehicle.
Reference Information
Schematic Reference
SIR Schematics ([1][2]Air Bag Systems)
Connector End View Reference
Component Connector End Views (Connector Views)
Description and Operation
SIR System Description and Operation (Description and Operation)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
Important:
* When removing connectors inspect for damage, corrosion or poor connection. Damage or corrosion in the following requires repair or replacement of the affected component/connector.
* PPS module
* SDM module
* PPS module harness connector
* SDM wiring harness connector
1. Ignition ON, verify that DTC B0081 is the only DTC set in the SDM or PPS module.
• If any other DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (Diagnostic Trouble Code (DTC) List - Vehicle).
2. Verify DTC B0081 0F, DTC B0081 3A, DTC B0081 39, or DTC B0081 71 is not set in the SDM. If any of these DTCs set in the SDM diagnose the following:
* SDM DTC B0081 0F:
• If DTC B0081 0F sets in the SDM then the PPS module will set DTC B0081 4B or DTC B0081 5A. Refer to step #3 and diagnose the PPS module DTC's. By diagnosing these two DTC's in the PPS module, DTC B0081 0F will be fixed in the SDM.
* SDM DTC B0081 3A:
• Either an incorrect replacement PPS module or SDM was placed in this vehicle. Check and make sure the part #'s are correct for each module. If both part #'s are correct clear this DTC and see if DTC B0081 3A resets as a current DTC. If DTC B0081 3A resets then replace the PPS module. Clear DTCs again and check if DTC B0081 3A sets as current again. If DTC B0081 3A sets again then replace the SDM.
* SDM DTC B0081 39:
• If DTC B0081 39 sets in the SDM then replace the PPS module.
* SDM DTC B0081 71:
• If DTC B0081 71 sets in the SDM check and see if the SDM also sets DTC U0170. If DTC U0170 is set in the SDM then diagnose DTC U0170. Refer to Diagnostic Trouble Code (DTC) List - Vehicle (Diagnostic Trouble Code (DTC) List - Vehicle). If DTC U0170 is not set in the SDM then check the connections at the SDM and PPS module. Clear DTC's and check if DTC B0081 71 sets as current. If DTC B0081 71 sets as current again then replace the PPS module.
3. Verify DTC B0081 4B, or DTC B0081 5A is not set in the PPS module. If either of these DTCs set in the PPS module diagnose the following:
* PPS DTC B0081 4B:
• If DTC B0081 4B sets in the PPS module if the correct calibration was not learned by the PPS module. Perform the Passenger Presence System Rezeroing procedure. Refer to Passenger Presence System Rezeroing (Tahoe Hybrid and Yukon Hybrid) (Passenger Presence System Rezeroing (Tahoe Hybrid and Yukon Hybrid)).
* PPS DTC B0081 5A:
• If DTC DTC B0081 5A sets in the PPS module check the connections at the SDM and PPS module. Clear the DTC's and check if DTC B0081 5A sets again in the PPS module. If DTC B0081 5A sets again replace the PPS module.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* SIR/SRS Wiring Repairs (SIR/SRS Wiring Repairs)
* Control Module References (Programming and Relearning) for PPS module and SDM replacement, setup, and programming