B3567
DTC B3567
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B3567 01
- Driver Information Center Select Switch Circuit Short to Battery
DTC B3567 59
- Driver Information Center Select Switch Circuit/Component Protection Time-Out
Diagnostic Fault Information
Circuit/System Description
The driver information center (DIC) switch is a multiplexed switch. Battery power is provided to the DIC switch via the instrument panel cluster (IPC). The DIC switch signal circuit is pulled up to battery voltage in the IPC. The IPC also provides the DIC switch with a low reference circuit. The switch input to the IPC is pulled low or grounded when a switch is activated. The DIC switch is a momentary contact switch that connects a series of resistors in a resistor ladder format. The IPC monitors the DIC switch signal circuit to determine the DIC switch inputs. Each switch state corresponds to a certain resistance value. The IPC determines the switch pressed by the voltage drop across the resistors. A stuck switch or a short to battery sets a DTC.
The Trip/Fuel switch is monitored on a separate circuit provided by the IPC. The TRIP/FUEL driver information center select menu switch signal circuit is monitored for a stuck switch but not a short to battery.
Conditions for Running the DTC
The ignition is in ACCESSORY or RUN.
Conditions for Setting the DTC
B3567 59
The IPC detects that the DIC switch is stuck.
B3567 01
The IPC detects that the DIC switch signal circuit is shorted to battery.
Action Taken When the DTC Sets
The IPC ignores the DIC switch inputs.
Conditions for Clearing the DTC
* The DTC becomes history when the conditions for setting the DTC are no longer present.
* The history DTC clears after 40 malfunction-free warm-up cycles.
Diagnostic Aids
* When the Trip/Fuel switch is stuck, all other DIC switches will function correctly. When any of the DIC switches are stuck, only the Trip/Fuel switch functions correctly.
* Only the DIC switch signal circuit can be diagnosed as shorted to battery.
Reference Information
Schematic Reference
Instrument Cluster Schematics (Instrument Cluster Schematics)
Connector End View Reference
Component Connector End Views (Connector End Views By Name)
Description and Operation
Driver Information Center (DIC) Description and Operation (Driver Information Center (DIC))
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
Ignition ON, verify that when the DIC switches are pressed and released the DIC scan tool parameters toggle between Active and Inactive.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the DIC switch assembly.
2. Ignition OFF, test for less than 1 ohm between the low reference circuit terminal 2 and ground.
• If greater than the specified range, test the low reference circuit for an open/high resistance.
3. Ignition OFF, test for less than 5 ohms between the ground terminal 6 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
4. Ignition ON, verify that all of the scan tool DIC Switch parameters are Inactive.
• If any are not Inactive, test the signal circuit terminal listed below for a short to ground. If the circuit tests normal, replace the IPC.
* Signal Terminal 1
* Signal Terminal 3
5. Ignition ON, install a 3-A fused jumper wire between the signal circuit terminal 1 and the low reference circuit terminal 2. Verify the scan tool DIC Switch parameters, except the DIC Fuel Info. parameter, are Active.
• If any are not Active, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the IPC.
6. Ignition ON, install a 3-A fused jumper wire between the signal circuit terminal 3 and ground. Verify the scan tool DIC Fuel Info. parameter is Active.
• If not Active, test the signal circuit for a short to voltage or and open/high resistance. If the circuit tests normal, replace the IPC.
7. If all the circuits test normal, test or replace the DIC switch assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Driver Information Display Switch Replacement (Service and Repair)
* Control Module References (Programming and Relearning) for IPC replacement, setup and programming