P1EAA
DTC P1EAA
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptor
DTC P1EAA
- Hybrid/EV Battery Voltage Balance Processor Multiplexer Performance
Circuit/System Description
The Hybrid/EV Battery Pack contains a total of 32 cell groups in the Hybrid/EV Battery Pack assembly. These cell groups are electrically connected in series. Each individual cell group is rated at 3.7 V, for a nominal system voltage of 118 V DC. The battery cells are grouped together into two sections, each with 16 cell groups.
The Battery Energy Control Module monitors the voltage of the 32 battery cell groups. A voltage sense circuit is attached to each individual cell group. Each of these circuits terminate at a connector located on the top surface of the battery section. A serviceable auxiliary battery wiring harness connectors the voltage sense circuits to the Battery Energy Control Module, located directly above the Hybrid/EV Battery Pack.
To ensure proper battery function and lengthen battery life, the battery energy control processor balances the voltage of the cells so that each cells maintains the same voltage level. The Battery Energy Control Module uses internal voltage gates to transfer voltage from cells with a higher voltage level to those cells with a lower voltage level. This voltage balancing is an internal function to the Battery Energy Control Module.
The cell voltages are read through multiplexer circuits which take the voltages from multiple battery cells and supplies them to one single analog to digital converter. To determine if the multiplexer is operating correctly, the balancing gates are operated by the Battery Energy Control Module one at a time, shifting each cell voltage while the balance gate is on. This cell voltage pattern is analyzed by the Starter/Generator Control Module to determine if there is a cell voltage multiplexer malfunction.
Conditions for Running the DTC
* Ignition mode transitions from RUN or CRANK to OFF.
* Contactor status is open.
* Propulsion system active while contactors are open for greater than 2.5 seconds is not true.
* DTC U182A is not set.
Conditions for Setting the DTC
* The balance process did not occur at ignition OFF.
* The balance process occurred at any time other than ignition OFF.
* The cell voltage movement during the balance process is more than 0.1 V from the expected voltage movement.
Action Taken When the DTC Sets
* DTC P1EAA is a type A DTC.
* The vehicle operates in a low battery mode with the high voltage contactors closed, but no hybrid functions will occur.
Conditions for Clearing the DTC
DTC P1EAA is a type A DTC.
Reference Information
Schematic Reference
Hybrid/EV Energy Storage Schematics
Connector End View Reference
Component Connector End Views Sunshade - Left
Description and Operation
Drive Motor Battery System Description
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References Control Module References for scan tool information
Special Tools
EL-48900 - HEV Safety Kit
For equivalent regional tools, refer to Special Tools .
Circuit/System Verification
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure includes the following steps:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 15 meters (50 feet) of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves with leather protectors at all times when working with the high voltage battery assembly, whether the system is energized or not.
Failure to follow the procedures may result in serious injury or death.
Danger: The eAssist battery pack assembly will utilize an exchange program. Please consult the most recent revision of bulletin/PI# PIC5520, available in Service Information (SI), for a list of approved eAssist battery pack assembly service procedures. Components that may be removed and serviced without exchanging the complete battery pack assembly are identified in the bulletin/PI. Please contact the GM Technical Assistance Center (1-877-446-8227) if you have any questions.
1. Verify no communication DTCs are set in the K59 Starter/Generator Control Module.
• If any communication DTCs are set in the K59 Starter/Generator Control Module
Refer to Diagnostic Trouble Code (DTC) List - Vehicle Diagnostic Trouble Code (DTC) List - Vehicle.
• If no communication DTCs are set in the K59 Starter/Generator Control Module
2. Verify DTC P1A5E or P1A5F are not set.
• If DTC P1A5E or P1A5F is set
Refer to DTC P1A5E or P1A5F P1A5E.
• If DTC P1A5E and P1A5F are not set
3. Verify DTC P1A60 is not set.
• If DTC P1A60 is set
Refer to DTC P1A60 P1A60.
• If DTC P1A60 is not set
4. Verify DTC P1EAA or P1EAC is not set as current.
• If DTC P1EAA or P1EAC is set as current
Replace the K16 Battery Energy Control Module.
Note: DTC P1EAA or P1EAC may be difficult to reproduce and no repair should be made unless the DTC is set as current. Operate the vehicle within the Conditions for Running the DTC when attempting to reproduce the DTC.
• If DTC P1EAA or P1EAC is not set or is set as history
5. All OK.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the repair.
Control Module References Control Module References for Battery Energy Control Module replacement, programming, and setup