Instrument Panel Service Positioning (with SLT)
Instrument Panel Service Positioning (with SLT)
Special Tools
J 42640 - Steering Column Anti-Rotation Pin
Removal Procedure
Caution:
With wheels of the vehicle facing straight ahead, secure the steering wheel utilizing steering column anti-rotation pin, steering column lock, or a strap to prevent rotation. Locking of the steering column will prevent damage and a possible malfunction of the SIR system. The steering wheel must be secured in position before disconnecting the following components:
* The steering column
* The intermediate shaft(s)
* The steering gear
After disconnecting these components, do not rotate the steering wheel or move the front tires and wheels. Failure to follow this procedure may cause the SIR coil assembly to become un-centered and cause possible damage to the SIR coil. If you think the SIR coil has became un-centered, refer to your specific SIR coil's centering procedure to re-center SIR Coil.
1. Lock the steering column through the access hole in the steering column shroud using the J 42640 - pin.
2. Remove the steering shaft coupling nut (1) and bolt (2) at the steering column.
3. Remove the front seats. Refer to Front Seat Replacement - Bucket Front Seat Replacement - Bucket.
4. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection (TP2) Battery Negative Cable Disconnection and Connection (TP2)Battery Negative Cable Disconnection and Connection (Single Battery) Battery Negative Cable Disconnection and Connection (Single Battery).
5. Remove the front floor console. Refer to Front Floor Console Replacement (without RPO SLT) Front Floor Console Replacement (without RPO SLT)Front Floor Console Replacement (with RPO SLT) Front Floor Console Replacement (with RPO SLT).
6. Remove the instrument panel outer trim covers. Refer to Instrument Panel Outer Trim Cover Replacement (without RPO SLT) Instrument Panel Outer Trim Cover Replacement (without RPO SLT)Instrument Panel Outer Trim Cover Replacement (with RPO SLT) Instrument Panel Outer Trim Cover Replacement (with RPO SLT).
7. Remove the windshield pillar garnish moldings. Refer to Windshield Pillar Garnish Molding Replacement Windshield Pillar Garnish Molding Replacement.
8. Remove the instrument panel upper trim panel with windshield defroster nozzle grille. Refer to Instrument Panel Upper Trim Panel with Windshield Defroster Nozzle Grille Replacement (with RPO SLT) Instrument Panel Upper Trim Panel with Windshield Defroster Nozzle Grille Replacement (with RPO SLT)Instrument Panel Upper Trim Panel with Windshield Defroster Nozzle Grille Replacement (without RPO SLT) Instrument Panel Upper Trim Panel with Windshield Defroster Nozzle Grille Replacement (without RPO SLT).
9. Tape the ambient light sensor to the instrument panel upper trim panel to ensure it does not fall behind the instrument panel assembly during reinstallation.
10. Remove the right and left body hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement Body Hinge Pillar Trim Panel Replacement.
11. Remove the instrument panel center support bracket. Refer to Instrument Panel Center Support Bracket Replacement Instrument Panel Center Support Bracket Replacement.
12. Note location and routing of the instrument panel wiring harness prior to removal in order to ensure proper installation.
13. On the right side of the instrument panel.
* Disconnect the electrical connections to the instrument panel right electrical center.
* Disconnect the electrical connection for the instrument panel inflatable restraint module.
* Disconnect the radio antennas.
* Release the wire looms securing the wiring harnesses to the right side of the instrument panel.
14. On the left side of the instrument panel.
* Disconnect the electrical connections to the instrument panel left electrical center.
* Disconnect the ground wires from the upper left cowl panel.
* Remove the body wiring harness junction block from its bracket to allow movement in the body harness.
* Release the wire looms securing the wiring harnesses to the left side of the instrument panel.
15. Remove the 4 bolts (1) securing the instrument panel upper trim panel to the cowl.
16. Remove the 2 bolts (1) securing the instrument carrier support to the cowl.
These bolts are located down inside the instrument panel and can be seen through the windshield.
17. Remove the 4 bolts (1) releasing the instrument panel assembly from the vehicle.
18. With the aid of an assistant pull the instrument panel assembly (1) rearward in the vehicle until the locator pin on each side clears the opening.
19. The person on the right side of the instrument panel should pivot the instrument panel inward toward the center of the vehicle until enough clearance is gained to access the HVAC module.
20. Set the instrument panel assembly down and adequately support it in order to prevent any damage.
Installation Procedure
1. With the aid of an assistant.
* Lift the instrument panel assembly (1) up and align the locator pins to the openings in the hinge pillars.
* Push the instrument panel forward until the instrument panel is in vehicle position.
2. Loosely install the 4 bolts (1) on the outer ends of the instrument panel.
3. Loosely install the 2 bolts (1) securing the instrument panel carrier support to the cowl.
Caution:
Refer to Fastener Caution Fastener Caution.
4. Tighten the 6 bolts securing the instrument panel to the vehicle.
Tighten the bolts to 22 Nm (16 lb ft).
5. Install the 4 bolts (1) securing the instrument panel upper trim panel to the cowl.
Tighten the bolts to 9 Nm (80 lb in).
6. On the left side of the instrument panel.
* Connect the wire looms securing the wiring harnesses to the left side of the instrument panel.
* Install the body wiring harness junction block into its bracket.
* Connect the ground wires to the upper left cowl panel.
Tighten the nut to 9 Nm (80 lb in).
* Connect the electrical connections to the instrument panel left electrical center.
7. On the right side of the instrument panel.
* Connect the wire looms securing the wiring harnesses to the right side of the instrument panel.
* Connect the radio antennas.
* Connect the electrical connection for the instrument panel inflatable restraint module.
* Connect the electrical connections to the instrument panel right electrical center.
8. Install the instrument panel center support bracket. Refer to Instrument Panel Center Support Bracket Replacement Instrument Panel Center Support Bracket Replacement.
9. Install the right and left body hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement Body Hinge Pillar Trim Panel Replacement.
10. Remove the instrument panel upper trim panel with windshield defroster nozzle grille. Refer to Instrument Panel Upper Trim Panel with Windshield Defroster Nozzle Grille Replacement (with RPO SLT) Instrument Panel Upper Trim Panel with Windshield Defroster Nozzle Grille Replacement (with RPO SLT)Instrument Panel Upper Trim Panel with Windshield Defroster Nozzle Grille Replacement (without RPO SLT) Instrument Panel Upper Trim Panel with Windshield Defroster Nozzle Grille Replacement (without RPO SLT).
11. Install the windshield pillar garnish moldings. Refer to Windshield Pillar Garnish Molding Replacement Windshield Pillar Garnish Molding Replacement.
12. Install the instrument panel outer trim covers. Refer to Instrument Panel Outer Trim Cover Replacement (without RPO SLT) Instrument Panel Outer Trim Cover Replacement (without RPO SLT)Instrument Panel Outer Trim Cover Replacement (with RPO SLT) Instrument Panel Outer Trim Cover Replacement (with RPO SLT).
13. Install the front floor console. Refer to Front Floor Console Replacement (without RPO SLT) Front Floor Console Replacement (without RPO SLT)Front Floor Console Replacement (with RPO SLT) Front Floor Console Replacement (with RPO SLT).
14. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection (TP2) Battery Negative Cable Disconnection and Connection (TP2)Battery Negative Cable Disconnection and Connection (Single Battery) Battery Negative Cable Disconnection and Connection (Single Battery).
15. Install the front seats. Refer to Front Seat Replacement - Bucket Front Seat Replacement - Bucket.
16. Install the steering shaft coupling nut (1) and bolt (2) at the steering column.
Tighten the nut and bolt to 50 Nm (37 lb ft).
17. Remove the J 42640 - pin from the steering column.