Transmission Case Assemble (Gen 1)
Transmission Case Assemble (Gen 1)
Special Tools
* 3-9506289 - Universal Adapter
* J-840733 - Driver
* R-0007758 - Holding Fixture
* R-0007761 - Universal Handle
* R-0007770 - Holding Fixture Adapter Plates
* T-9804669 - Seal Installer
* T-0307000 - Extractor and Driver Fixture
For equivalent regional tools, refer to Special Tools F13-5/F15-5/F17-5 (M26) - Manual Transmission.
1. Install the reverse idler gear shaft retaining ball (2).
2. Install the reverse idler gear shaft (1).
3. Using T-9804669 - seal installer (2) and R-0007761 - handle (1), install the mainshaft bearing (3) into the case.
4. Install the mainshaft bearing retaining ring (1).
5. Install the input shaft (3), reverse idler gear (2) and mainshaft (1) onto the T-0307000 - driver fixture with top plate removed.
6. Guide the shafts (1-2) into the bores, and support the reverse idler gear (3) while pressing into the case.
7. Using the T-0307000 - driver fixture, press the 5th gear bearing race (1) onto the mainshaft.
8. Install the case and shafts assembly onto the R-0007770 - adapter plates (1) and R-0007758 - holding fixture (2).
9. Install the input shaft bearing retaining ring (1).
10. Install the 1st and 2nd shift fork (2).
11. Install the 1st and 2nd shift shaft (1).
12. Install the 1st and 2nd shift fork pin (3) to the dimension "a" depth of 2 mm (0.80 in).
13. Install the gearshift rod (1) into the transmission case.
14. Install the 5th shift blocking guide (1) into the transmission case.
15. Install the 3rd and 4th shift fork (2).
16. Install the 3rd and 4th shift shaft (1).
17. Install the 3rd and 4th shift fork pin (3) to the dimension "a" depth of 2 mm (0.80 in).
18. Install the reverse shift fork (2).
19. Install the reverse shift shaft (1).
20. Install the reverse shift fork pin (3) to the dimension "a" depth of 2 mm (0.80 in).
21. Using a plastic hammer or equivalent install the 4 shift shaft detent sleeves (1-4) into the transmission case until they stop.
Note:
Engage the shift shafts into 3rd gear and 5th gear as indicated with arrows to install the interlock pin connector.
22. Install the shift shaft interlock pin connector (1).
23. Using thread locking compound install the shift shaft interlock pin connector bolts (2) and tighten to 7 Nm (62 lb in).
Note:
Move shift forks into neutral position.
24. Install the parking pawl (2).
Caution:
Refer to Fastener Caution Fastener Caution.
25. Using thread locking compound install the parking pawl retaining bolts (1) and tighten to 7 Nm (62 lb in).
26. Remove case and shafts assembly from R-0007770 - adapter plates and install onto T-0307000 - driver fixture.
27. Using J-840733 - driver, press the 5th gear, driving (1) onto the input shaft.
28. Install a NEW 5th gear retaining ring (1).
29. Install the 5th gear bearing assembly (3).
30. Install the 5th gear assembly, driven (2).
31. Install the 5th gear blocking ring (1).
32. Ensure that the synchronizer assembly (1) is functioning properly, refer to Synchronizers Cleaning and Inspection Synchronizers Cleaning and Inspection and Synchronizers Assemble Synchronizers Assemble.
33. Using the J-840733 - driver and a press, install the 5th gear synchronizer assembly (1).
34. Install the 5th gear sychronizing hub retaining ring (1).
35. Remove the case and shafts assembly from the T-0307000 - driver fixture.
36. Install R-0007770 - adapter plates (1) onto case (2) and then attach to R-0007758 - holding fixture (3).
37. Install the 5th shift fork shoes (3).
38. Install the 5th shift fork bracket assembly (2).
39. Using thread locking compound install the 5th shift fork bracket bolts (1) and tighten to 22 Nm (16 lb ft).
40. Remove the transmission case, from the R-0007770 - adapter plates (1) the R-0007758 - holding fixture and 3-9506289 - adapter.