Operation CHARM: Car repair manuals for everyone.

P0116



DTC P0116

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Initial Inspection and Diagnostic Overview
* Review Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC P0116
- Engine Coolant Temperature (ECT) Sensor Performance

Diagnostic Fault Information






Typical Scan Tool Data






Circuit/System Description

The engine coolant temperature (ECT) sensor is a variable resistor that measures the temperature of the engine coolant. The engine control module (ECM) supplies 5 volts to the ECT sensor signal circuit, and supplies a ground to the low reference circuit. The ECM uses this high side coolant rationality diagnostic to determine if the input from the ECT sensor is skewed warmer than normal. The internal clock of the ECM will record the amount of time the ignition is OFF. If the calibrated ignition OFF timer is met at start-up, the ECM will compare the temperature difference between the ECT and the intake air temperature (IAT), to determine if the temperatures are within an acceptable operating range of each other.

Conditions for Running the DTC

* DTCs P0112, P0113, P0117, P0118, P0502, P0503, P0601, P0603, P062F, P2610 are not set.
* The vehicle has had a minimum ignition OFF time of 10 hours.
* The ignition is ON.
* The start-up IAT is more than -7°C (+19°F).
* The Fuel Level Sensor parameter is more than 5 percent.
* This DTC runs once per ignition cycle when the above conditions are met.

Conditions for Setting the DTC

* The ECM detects a temperature difference at power-up that indicates that the ECT sensor is 30°C (54°F) more than the IAT sensor.
OR
* The ECM detects a temperature difference at power-up that indicates that the ECT sensor is 10°C (18°F) more than the IAT sensor, and the time spent cranking the engine is more than 10 seconds, when the fuel level is more than 5 percent.
OR
* With the power-up IAT more than -7°C (+19°F), the ECM detects a temperature difference at power-up that indicates that the ECT sensor is 20°C (36°F) more than the IAT sensor. Then the vehicle must be driven for more than 6 minutes and 40 seconds at more than 40 km/h (25 mph). If the IAT sensor then decreases more than 4°C (7°F), an engine block heater was detected and the test is aborted. If the IAT sensor does not decrease, an engine block heater was not detected and DTC P0116 will set.

Action Taken When the DTC Sets

DTC P0116 is a Type B DTC.

Conditions for Clearing the MIL/DTC

DTC P0116 is a Type B DTC.

Diagnostic Aids

* Inspect the ECT sensor terminals for corrosion and for engine coolant leaking through the sensor. Engine coolant that is leaking through the sensor will create a high resistance short to ground. This condition results in less voltage on the ECT sensor signal circuit, which is interpreted by the ECM as a warmer ECT.
* An IAT sensor that is skewed colder at various ambient temperatures due to greater resistance than is normal will increase the range between these two sensors. Measure and record the resistance of the IAT sensor at various ambient temperatures, then compare those measurements to the Temperature vs Resistance table. Refer to Temperature Versus Resistance.
* A slight to moderate resistance in the IAT sensor signal circuit or low reference circuit will increase the range between these two sensors. This condition results in a greater voltage on the IAT sensor signal circuit, which is interpreted by the ECM as a colder IAT.

Circuit/System Verification

1. Ignition OFF, inspect the cooling system surge tank for the proper coolant level.
2. Ignition OFF for 8 hours or greater.
3. Ignition ON, observe the scan tool IAT and ECT sensor parameters. The ECT, IAT, and ambient temperature should be within 6°C (11°F) of each other.
4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the ECT sensor.
2. Ignition OFF for 90 seconds, test for less than 5 ohms between the low reference circuit terminal A and ground.

^ If greater than the specified range, test the low reference circuit terminal A for an open/high resistance. If the circuit tests normal, replace the ECM.

3. Ignition ON, verify the scan tool ECT parameter is colder than -39°C (-38°F).

^ If greater than the specified range, test the signal circuit terminal B for a short to ground. If the circuit tests normal, replace the ECM.

4. Install a 3A fused jumper wire between the signal circuit terminal B and the low reference circuit terminal A. Verify the scan tool ECT parameter is greater than 149°C (300°F).

^ If less than the specified range, test the signal circuit terminal B for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.

5. If all circuits test normal, test or replace the ECT sensor.

Component Testing

Measure and record the resistance of the ECT sensor at various ambient temperatures, then compare those measurements to the Temperature vs Resistance table. Refer to Temperature Versus Resistance.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure. Verification Tests

* Engine Coolant Temperature Sensor Replacement