P00C9
DTC P00C9 or P00CA
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P00C9
- Fuel Pressure Regulator 1 High Control Circuit Low Voltage
DTC P00CA
- Fuel Pressure Regulator 1 High Control Circuit High Voltage
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
The engine control module (ECM) controls the fuel rail pressure by controlling fuel pressure regulator 1 and fuel pressure regulator 2 simultaneously to achieve the desired fuel rail pressure. Fuel pressure regulator 1 is located on the fuel injection pump and controls the amount of fuel allowed into the high pressure side of the injection pump. If the ECM detects a fault on either of the fuel pressure regulator 1 circuits a DTC will be set.
Conditions for Running the DTC
* Engine speed is greater than 600 RPM.
* Battery voltage is greater than 11 V.
Conditions for Setting the DTC
DTC P00C9
* The ECM detects low voltage on the supply voltage circuit of fuel pressure regulator 1.
* The above condition exists for greater than 1 s.
DTC P00CA
* The ECM detects high voltage on the supple voltage circuit of fuel pressure regulator 1.
* The above condition exists for greater than 1 s.
Action Taken When the DTC Sets
* DTC's P00C9 and P00CA are Type A DTCs
* The ECM commands the engine to operate in the Reduced Engine Power mode.
* The message center displays Reduced Engine Power.
Conditions for Clearing the DTC
DTC's P00C9 and P00CA are Type A DTCs
Diagnostic Aids
* No driveablity concerns may be present if the fuel pressure regulator 1 supply voltage circuit is shorted to voltage.
* If the fuel system pressure is actually too high, a fuel knock condition will exist.
Reference Information
Schematic Reference
Engine Controls Schematics ([1][2]Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector End Views By Name)
Description and Operation
Fuel System Description (Fuel System Description)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (Powertrain Diagnostic Trouble Code (DTC) Type Definitions)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
1. Engine running, observe the following scan tool parameters:
* Fuel Press. Reg. 1 High Ctrl. Ckt. Short Gnd Test Status
* Fuel Press. Reg. 1 High Ctrl. Ckt. Short Volts Test Status
Each parameter should display OK or Not Run.
2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the Q45A fuel pressure regulator 1.
2. Connect a test lamp between the Fuel Rail Pressure Regulator High Control circuit terminal 1 and ground. Verify the test lamp illuminates for 2-3 seconds after ignition ON.
• If the test lamp does not illuminate, test the Fuel Rail Pressure Regulator High Control circuit for an open, high resistance or short to ground. If the circuit tests normal, replace the K20 engine control module.
• If the test lamp remains illuminated, test the Fuel Rail Pressure Regulator High Control circuit for a short to B+. If the circuit tests normal, replace the K20 engine control module.
3. If all circuits test normal, replace the Q45A fuel pressure regulator 1.
Repair Instructions
Note: During code clearing, the ECM must be powered down. Power down is achieved by turning off the ignition key and waiting for loss of communication, indicating power down. The time to power down may vary from vehicle to vehicle. After power down is achieved, turn the ignition key to the ON position and clear the trouble code using the scan tool clear code function and power down ECM. Repeat power down if the trouble code does not clear on first attempt.
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Fuel Pressure Regulator Replacement (Service and Repair)
* Perform the scan tool Diesel Particulate Filter (DPF) Regeneration Enable (Diesel Particulate Filter (DPF) Regeneration Enable) procedure if the scan tool DPF Soot Mass is less than 30 g. If the scan tool DPF Soot Mass is 30 g or greater, perform the Diesel Particulate Filter (DPF) Service Regeneration (Diesel Particulate Filter (DPF) Service Regeneration) procedure.
* Control Module References (Programming and Relearning) for ECM replacement, programming, and setup.