Engine Oil Pressure Indicator Malfunction
Engine Oil Pressure Indicator Malfunction
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
The engine oil pressure (EOP) sensor changes voltage based on the engine oil pressure. The EOP sensor is a 3-wire sensor comprising of the signal circuit, the low reference circuit and the 5-volt reference circuit. The engine control module (ECM) supplies 5 volts to the EOP sensor via the 5-volt reference circuit and provides ground via the EOP low reference circuit. The ECM monitors the signal circuit of the EOP sensor to determine the EOP sensor voltage is within the normal operating range of approximately 1-4 volts. When the engine oil pressure is high, the EOP sensor voltage is high and the ECM senses a high signal voltage. When the engine oil pressure is low, the EOP sensor voltage is low and the ECM senses a low signal voltage. The ECM sends the EOP information via the serial data circuit to the body control module (BCM). The BCM then sends the EOP information to the instrument panel cluster (IPC) via the serial data circuit.
Reference Information
Schematic Reference
Instrument Cluster Schematics (Instrument Cluster Schematics)
Connector End View Reference
Component Connector End Views (Connector End Views By Name)
Description and Operation
* Instrument Cluster Description and Operation (Instrument Cluster)
* Indicator/Warning Message Description and Operation (Indicator/Warning Message)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
Scan Tool Reference
Control Module References (Control Module References) for scan tool information
Circuit/System Verification
1. Engine running, observe the scan tool Engine Oil Pressure Sensor parameter. The reading should be between 41-448 kPa (6-65 psi).
2. Verify the engine oil pressure, refer to:
* Oil Pressure Diagnosis and Testing (Oil Pressure Diagnosis and Testing) for the 4.8L, 5.3L, 6.0L, 6.2L or 7.0L engines
* Oil Pressure Diagnosis and Testing (Oil Pressure Diagnosis and Testing) for the 6.0L (LFA) engine.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the engine oil pressure (EOP) sensor.
2. Ignition OFF, test for less than 1.0 ohm between the low reference circuit terminal 1 and ground.
• If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 2 and ground.
• If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.
• If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.
4. Verify the scan tool Engine Oil Pressure Sensor parameter is less than 8 kPa (1.2 psi).
• If greater than the specified range, test the signal circuit terminal 3 for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.
5. Install a 3A fused jumper wire between the signal circuit terminal 3 and the 5-volt reference circuit terminal 2. Verify the scan tool Engine Oil Pressure Sensor parameter is greater than 550 kPa (80 psi).
• If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.
6. Ignition ON, command the indicators OFF with the scan tool.
• If the EOP indicator does not turn OFF, replace the IPC.
7. If all circuits test normal, test or replace the EOP sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Engine Oil Pressure Sensor and/or Switch Replacement (Service and Repair) for the 6.0L (LFA) engine
* Engine Oil Pressure Sensor and/or Switch Replacement (Service and Repair) for the 4.8L, 5.3L, 6.0L, 6.2L, or 7.0L engine.
* Control Module References (Control Module References) for the PCM or IPC replacement, setup, and programming