Fluid Leak Diagnosis
Fluid Leak Diagnosis
General Method
1. Verify that the leak is transmission fluid.
Caution: Do not clean using brake cleaner or other reactive solvents as these solvents can damage rubber gaskets, seals and bushings.
2. Thoroughly clean the suspected leak area using a rag.
Note: Do not idle vehicle, this will not actuate transmission systems, and do not drive the vehicle on the freeway as this will splatter oil inhibiting leak diagnosis.
3. Operate the vehicle for 15-20 minutes under city driving conditions until normal operating temperatures are reached.
4. Park the vehicle over clean paper or cardboard.
5. Shut OFF the engine.
6. Look for fluid spots on the paper.
7. Make the necessary repairs.
Powder Method
Caution: Do not clean using brake cleaner or other reactive solvents as these solvents can damage rubber gaskets, seals and bushings.
1. Thoroughly clean the suspected leak area using a rag.
2. Apply an aerosol type leak tracing powder to the suspected leak area.
Note: Do not idle vehicle, this will not actuate transmission systems, and do not drive the vehicle on the freeway as this will splatter oil inhibiting leak diagnosis.
3. Operate the vehicle for 15-20 minutes under city driving conditions until normal operating temperatures are reached.
4. Shut OFF the engine.
5. Inspect the suspected leak area.
6. Trace the leak path through the powder in order to find the source of the leak.
7. Make the necessary repairs.
Dye and Black Light Method
A fluid dye and black light kit is available from various tool manufacturers.
1. Follow the manufacturer's instructions in order to determine the amount of dye to use.
2. Detect the leak with the black light.
3. Make the necessary repairs.
Find the Cause of the Leak
Pinpoint the leak and trace the leak back to the source. You must determine the cause of the leak in order to repair the leak properly. For example, if you replace a gasket, but the sealing flange is bent, the new gasket will not repair the leak. You must also repair the bent flange. Before you attempt to repair a leak, check for the following conditions, and make repairs as necessary:
Gaskets
* Fluid level/pressure is too high
* Plugged vent or drain-back holes
* Improperly tightened fasteners
* Dirty or damaged threads
* Warped flanges or sealing surface
* Scratches, burrs, or other damage to the sealing surface
* Damaged or worn gasket
* Cracking or porosity of the component
* Improper sealant used, where applicable
* Incorrect gasket
Seals
* Fluid level/pressure is too high
* Plugged vent or drain-back holes
* Damaged seal bore
* Damaged or worn seal
* Improper installation
* Cracks in component
* Manual or output shaft surface is scratched, nicked, or damaged
* Loose or worn bearing causing excess seal wear
Possible Points of Fluid Leaks
Transmission Oil Pan
* Incorrectly tightened oil pan bolts
* Improperly installed or damaged oil pan gasket
* Damaged oil pan or mounting face
* Incorrect oil pan gasket
* Incorrectly tightened or damaged drain plug
Case Leak
* Damaged output speed sensor seal
* Damaged manual shaft seal
* Loose or damaged oil cooler connector fittings
* Worn or damaged propeller shaft oil seal
* Loose line pressure pipe plug
* HV 3 Phase cable lug box
* Porous casting warped dampener housing
Leak at the Dampener End
* Dampener leak in the weld area
* Dampener seal lip cut. Check the Dampener hub for damage
* Dampener seal bushing moved forward and damaged
* Dampener seal garter spring missing from the seal
* Porous casting of the transmission case or the oil pump
Leak at the Vent Pipe
* Overfilled system
* Water or coolant in the fluid; The fluid will appear milky
* Transmission case porous
* Incorrect fluid level indicator
* Plugged vent
* Drain-back holes plugged
* Mispositioned oil pump to case gasket, if equipped
Leak at the Case Extension
* Output shaft seal assembly - located in the case
* Output shaft seal assembly - located in the case extension
Leak Inspection Points
1 - 24-Way Connector Assembly or A/Trans Electrical Connector Passage Sleeve
2 - A/Trans Vent Pipe
3 - A/Trans Torque Dampener Housing Gasket
4 - A/Trans Fluid Cooler Pipe Fitting Seal
5 - Line Pressure Test Hole Plug or Auxiliary Pump Pressure Test Hole Plug
6 - Drive Motor/Generator Power Inverter Module Cable Housing Cover Seals
7 - Park Pawl Cover Seal
8 - Manual Shift Shaft Seal
9 - Transmission Fluid Fill Tube Seal
10 - A/Trans Rear Case Gasket
11 - Extension Assembly Gasket
12 - A/Trans Case Assembly
13 - Output Seal
14 - A/Trans Fluid Pan Gasket
15 - A/Trans Torque Dampener Seal
16 - A/Trans Torque Dampener Assembly
17 - A/Trans Fluid Pan Drain Plug O-Ring Seal