Antilock Brakes / Traction Control Systems: Description and Operation
BASIC KNOWLEDGE REQUIREDIt is important that you have a basic knowledge of the following items. Without this knowledge, it will be difficult to use the diagnostic procedures.
- Basic Electrical Circuits~-You should understand the basic theory of electricity and know the meaning of voltage., current (amps), and resistance (ohms). You should understand what happens in a circuit with an open or shorted wire. You should be able to read and understand a wiring diagram.
- Use of Circuit Testing Tools-You should know how to use a test light and how to bypass components to test circuits using fused jumper wires. You should be familiar with a digital multimeter. You should be able to measure voltage, resistance, and current, and be familiar with the controls and how to use them correctly.
ABS SYSTEM COMPONENTS
The ABS 5.3 Antilock Braking System (ABS) consists of a conventional hydraulic brake system plus antilock components. The conventional brake system includes a vacuum booster, master cylinder, front disc brakes, rear leading/trailing drum brakes, interconnecting hydraulic brake pipes and hoses, brake fluid level sensor and the BRAKE indicator.
The ABS components include a hydraulic unit, an Electronic Brake Control Module (EBCM), two system fuses, four wheel speed sensors (one at each wheel), interconnecting wiring, the ABS indicator, the EBD indicator (which is connected to the parking lamp) and the rear disk brakes.
The hydraulic unit with the attached EBCM is located on the right side of the vehicle.
The basic hydraulic unit configuration consists of hydraulic check valves, two solenoid valves for each wheel, a hydraulic pump, two accumulators, and two damper. The hydraulic unit controls hydraulic pressure to the front calipers and rear wheel cylinders by modulating hydraulic pressure to prevent wheel lockup.
Nothing in the hydraulic unit or the EBCM is serviceable. In the event of any failure, the entire ABS unit with attached EBCM must be replaced.
BASE BRAKING MODE
The baseline braking mode of the ABS 5.3 system used in this vehicle is a diagonal split system. In this system, one master cylinder circuit supplies pressure to the right front and the left rear brakes; the other circuit supplies pressure to the left front and the right rear brakes.
ANTILOCK BRAKING MODE - APPLY
If a wheel speed sensor detects a wheel locking up, the electronic brake control module (EBCM) closes the normally open inlet valve for the brake on that wheel to prevent adding more hydraulic pressure to that brake.
ANTILOCK BRAKING MODE - HOLD
The illustration shows this.
ANTILOCK BRAKING MODE - RELEASE
If the wheel locking tendency continues, the EBCM releases the hydraulic pressure at that brake by opening the outlet valve for that wheel.
EBD (Electronic Brake Force Distribution) SYSTEM
As an add-on logic to the ABS base algorithm, EBD works in it range in which the intervention thresholds for ABS control are not reached yet.
EBD ensures that the rear wheels are sensitively monitored for slip with respect to the front axle. If slip is detected, the inlet valves for the rear wheels are switched to pressure hold to prevent a further increase in pressure at the rear-wheel breaks, thus electronically reproducing a pressure- reduction function at the rear-wheel brakes.
The Benefits of EBD
- Elimination of conventional proportioning valve
- EBD utilizes the existing rear axle wheel speed sensor to monitor rear wheel slip.
- Based on many variables in algorithm a pressure hold, increase and/or decrease pulsetrain may be triggered at the rear wheels insuring vehicle stability
- Vehicle approaches the ideal brake force distribution (front to rear)
- Constant brake force distribution during vehicle lifetime.
- EBD function is monitored via ABS safety logic (conventional proportioning valves are not monitorable)
- "Keep alive" function.
TIRES AND ABS/EBD
Replacement Tires
Tire size is important for proper performance of the ABS system. Replacement tires should be the same size, load range, and construction as the original tires. Replace tires in axle sets and only with tires of the same Tire Performance Criteria (TPC) specification number. Use of any other size or type may seriously affect the ABS operation.
VALVE RELAY AND PUMP MOTOR RELAY
The valve relay and the motor pump relay are located inside the Electronic Brake Control Module (EBCM) and are not replaceable. If one should fail, replace the EBCM.