Fuel Tank Draining and Removal/Installation

FUEL TANK DRAINING AND REMOVAL/INSTALLATION PROCEDURE

WARNING: THE FUEL SYSTEM IS UNDER A CONSTANT PRESSURE EVEN WITH THE ENGINE OFF. BEFORE SERVICING THE FUEL TANK, FUEL SYSTEM PRESSURE MUST BE RELEASED. REFER TO THE FUEL SYSTEM PRESSURE RELEASE PROCEDURE BEFORE SERVICING THE FUEL TANK.

Two different procedures may be used to drain fuel tank (lowering tank or using DRB scan tool). When equipped with a diesel engine, the DRB scan tool cannot be used (no electric fuel pump).

The quickest draining procedure involves lowering the fuel tank.

As an alternative procedure, the electric fuel pump may be activated allowing tank to be drained at fuel rail connection. Refer to DRB scan tool for fuel pump activation procedures. Before disconnecting fuel line at fuel rail, release fuel pressure. Refer to the Fuel System Pressure Release Procedure. Attach end of special test hose tool number 6541, 6539, 6631 or 6923 at fuel rail disconnection (tool number will depend on model and/or engine application). Position opposite end of this hose tool to an approved gasoline draining station. Activate fuel pump and drain tank until empty.

If electric fuel pump is not operating, tank must be lowered for fuel draining. Refer to following procedures.

REMOVAL
1. Remove fuel tank filler tube cap.
2. Perform Fuel System Pressure Release procedure.
3. Disconnect negative battery cable at battery.
4. Raise vehicle on hoist.
5. Certain models are equipped with a separate grounding wire (strap) connecting the fuel fill tube assembly to the body. Disconnect wire by removing screw.
6. Open fuel fill door and remove screws mounting fuel filler tube assembly to body. Do not disconnect rubber fuel fill or vent hoses from tank at this time.
7. Place a transmission jack under center of fuel tank. Apply a slight amount of pressure to fuel tank with transmission jack.

Fuel Tank Mounting - Typical:

8. Remove fuel tank mounting strap nuts from mounting strap studs. If equipped, remove fuel tank shield bolts.
9. Lower fuel tank only enough to allow access to top of tank. The 2 tank fittings (where rubber fuel fill and vent hose connections are made) must be positioned above tank level. Rotate tank slightly to allow these fittings to be above tank level.

WARNING: WRAP SHOP TOWELS AROUND HOSES TO CATCH ANY GASOLINE SPILLAGE.

10. While working over left rear tire/wheel, disconnect rubber fuel vent hose at fuel tank (vent hose is the smallest of 2 hoses). Position fuel siphoning/ drain hose into this fitting at tank. Drain fuel into an approved portable holding tank or a properly labeled gasoline (or diesel fuel) safety container.
11. Disconnect rubber fuel fill hose at fuel tank.
12.

Fuel Pump Module - With 26 Or 34 Gallon Tank:

Fuel Pump Module - With 35 Gallon Tank:

a. While working over left rear tire/wheel, disconnect wiring harness connector from electrical connector at top of fuel pump module.
b. If equipped with 26 or 34 gallon fuel tank, two EVAP lines are connected to rollover valves. Disconnect EVAP line from rollover valve at top of module. Disconnect other EVAP line from rollover valve near rear of tank.

Rollover Valve Locations - With 35 Gallon Tank:

c. If equipped with 35 gallon fuel tank, two EVAP lines are connected to rollover valves. Disconnect EVAP lines from rollover valves at top- front and top-rear of fuel tank.
d. Disconnect fuel supply line at fuel filter/fuel pressure regulator supply fitting. Refer to Quick-Connect Fittings for procedures.
13. If fuel pump module removal is necessary, refer to Fuel Pump Module Removal/Installation.

INSTALLATION
1. If fuel pump module is being installed, refer to Fuel Pump Module Removal/Installation.
2. Place fuel tank on top of transmission jack.
3. Install rubber fill and vent lines to tank. Tighten hose clamps to 2.3 Nm (20 in. lbs.) torque.
4. Raise tank into position while guiding fill and vent hoses to body. Raise tank only enough to allow access to top of tank.
5.
a. Connect electrical connector to fuel pump module.
b. Connect EVAP hoses at rollover valves.
c. Connect fuel supply line at fuel filter/fuel pressure regulator. Refer to Quick-Connect Fittings for procedures.
6. Connect two mounting straps and mounting strap nuts.
7. Tighten strap nuts to 41 Nm (30 ft. lbs.) torque. Do not over tighten retaining strap nuts.
8. Remove transmission jack.
9. Connect fuel filler tube assembly to body.
10. If equipped, connect grounding wire (strap) and screw.
11. Refill fuel tank and inspect all hoses and lines for leaks.
12. Connect negative battery cable(s) to battery(s).