Part 1 of 2
FUEL CONTROLThe PCM controls the air/fuel ratio of the engine by varying fuel injector on time. Mass air flow is calculated by the speed density method using engine speed and manifold absolute pressure (IAT is a modifier in Speed Density).
Different fuel calculation strategies are used depending on the operational state of the engine. During crank mode, a prime shot fuel pulse is delivered followed by fuel pulses determined by a crank time strategy. Cold engine operation is determined via an open loop strategy until the O2 sensors have reached operating temperature. At this point, the strategy enters a closed loop mode where fuel requirements are based upon the state of the O2 sensors, engine speed, MAP, throttle position, air temperature, battery voltage, and coolant temperature.
ON-BOARD DIAGNOSTICS
The PCM has been programmed to monitor any circuit or system that has an effect on vehicle emissions, or is used by the PCM to determine the proper functionality of these systems. This monitoring is called "on-board diagnosis."
Certain criteria or, "arming conditions", must be met for a trouble code to be entered into the PCM memory. The criteria may be a range of: engine rpm, engine temperature, and/or input voltage to the PCM. If a problem is detected with a monitored circuit, and all of the criteria or arming conditions are met, a trouble code will be stored in the PCM.
It is possible that a trouble code for a monitored circuit may not be entered into the PCM memory even though a malfunction has occurred. This may happen because one of the trouble code criteria (arming conditions) has not been met.
The PCM compares input signal voltages from each input device with specifications (the established high and low limits of the range) that are preprogrammed for that device. If the input voltage is not within specifications and other trouble code criteria (arming conditions) are met, a trouble code will be stored in the PCM memory.
The On Board Diagnostics have evolved to the second Generation of Diagnostics referred to as OBDII. These OBDII Diagnostics control the functions necessary to meet the requirements of California OBDII and Federal OBD regulations. These requirements specify the inclusion of a Malfunction Indicator Light (MIL) located on the instrument panel for all 1994 and subsequent model-year passenger cars, light duty trucks, and medium-duty vehicles. The purpose of the MIL is to inform the vehicle operator in the event of the malfunction of any emission systems and components which can affect emissions and which provide input to, or receive output from, the PCM.
OBDII Monitor Operation:
The following table summarizes the various OBDII monitors operation.
TRANSMISSION CONTROL
The PCM also controls the 4 speed automatic transmissions utilizing electronic governor pressure control, eliminating the need for a separate transmission controller.
Transmission control is achieved through regulation of governor pressure using a Governor Pressure Solenoid valve. Valve position is controlled by pulse width modulation. Torque converter clutch and overdrive solenoids are also controlled by the PCM, as are the transmission relay and dashboard overdrive off lamp. PCM inputs affecting transmission operation include the throttle position sensor, output shaft speed sensor, vehicle speed, engine speed sensor (CKP), brake switch, ignition, overdrive ON/OFF switch, torque converter clutch solenoid, transmission temperature sensor, and governor pressure sensor.
The PCM continuously checks for internal transmission problems, electrical problems, and some hydraulic problems. When a problem is sensed, the PCM stores a diagnostic trouble code. Any of these codes cause the transmission to go into "default" mode. When the PCM detects a problem, the transmission will default to third gear. When this happens, the only transmission functions are:
- PARK and NEUTRAL
- REVERSE
- THIRD GEAR
- MANUAL SHIFTING of FIRST, SECOND and THIRD GEAR
No upshifts or downshifts are allowed. The position of the manual valve alone allows the ranges that are available. Although engine performance is seriously degraded while in this mode, it allows the owner to drive the vehicle in for service. The transmission can be shifted manually by quickly down- shifting into 1st to achieve 1st gear, then shifting to 2nd, then to third. However, default mode will not allow 4th gear or any EMCC operation.
Once the DRB III is in the RE transmission portion of the diagnostic program, it constantly monitors the PCM, updating the screens with switch, sensor, and input/output states, as well as displaying diagnostic trouble codes and default status.
Transmission Identification
The transmission part/identification numbers and codes are stamped on the left side of the case just above the oil pan gasket surface. The first letter/number group is the assembly part number. The next number group is the transmission serial number. Refer to this information when ordering replacement parts.
Governor Pressure Solenoid Valve
The solenoid valve generates the governor pressure needed for upshifts and downshifts. It is an electro-hydraulic device and is located in the governor body on the valve body transfer plate. The inlet side of the solenoid valve is exposed to normal transmission line pressure while in forward gears. The outlet side of the valve leads to the valve body governor circuit. The solenoid valve regulates line pressure to produce governor pressure. The average current supplied to the solenoid valve controls governor pressure. One amp current produces zero psi governor pressure. Zero amps set the maximum governor pressure. Current is regulated by modulation of the pulse width of a 512 Hz driver frequency. The transmission control relay supplies electrical power to the solenoid valve. Operating voltage is 12 volts (DC) and is provided through the relay's fused B+ contact. The solenoid is polarity sensitive. The PCM energizes the solenoid by grounding it through the power ground terminal on the PCM.
Governor Pressure Sensor
The governor pressure sensor measures output pressure of the governor pressure solenoid valve.
The sensor output signal provides the necessary feedback to the PCM. This feedback is needed to accurately control pressure. The unit is an absolute pressure device and the output is calibrated to be 0.35 to 0.65 volts at 14.7 psi (normal barometric pressure). Since this is an absolute pressure device, 0 psi calibration is required often to compensate for changing atmospheric pressure or altitude. This voltage measured at 0 psi is referred to as zero pressure offset.
Governor Shift Schedules
The electronic governor has several governor curves possible as opposed to a conventional governor, which has a single governor curve with two stages. These transmissions are mechanically and hydraulically the same as the ones they replace.
As with all-hydraulic transmissions, the vehicle shift speeds are determined by balancing a hydraulic pressure signal proportional to transmission output speed (called governor pressure) against a pressure signal determined by throttle position (called throttle pressure). The four curves are used during the following operating conditions.
- Low Transmission Fluid Temperature - When the transmission fluid is cold at or below 30 °F, the conventional governor can delay shifts, resulting in higher than normal shift speeds and harsh shifts. The electronically controlled low temperature governor pressure curve is higher than normal to make the transmission shift at normal speeds and sooner. The PCM uses a temperature sensor in the transmission oil sump to determine when low temperature governor pressure is needed.
- Wide-Open Throttle Operation - In Wide-open Throttle (WOT) mode, adaptive memory in the PCM assures that up-shifts occur at the preprogrammed optimum speed. WOT operation is deter- mined from the throttle position sensor, which is also a part of the emission control system. The initial setting for the WOT upshift is below the optimum engine speed. As WOT shifts are repeated, the PCM learns the time required to complete the shifts by comparing the engine speed when the shifts occur to the optimum speed. After each shift, the PCM adjusts the shift point until the optimum speed is reached. The PCM also considers vehicle loading, grade and engine performance changes due to high altitude in determining when to make WOT shifts. It does this by measuring vehicle and engine acceleration and then factoring in the shift time.
- Normal Operation - Normal operation is refined through the increased computing power of the PCM and through access to data on engine operating conditions provided by the PCM. This facilitated the development of a load adaptive shift strategy - the ability to alter the shift schedule in response to vehicle load conditions. One manifestation of this capability is grade "hunting" prevention - the ability of the transmission logic to delay an upshift on a grade if the engine does not have sufficient power to maintain speed in the higher gear. The 3-2 downshift and the potential for hunting between gears occurs with a heavily loaded vehicle or on steep grades. When hunting occurs, it is very objectionable because shifts are frequent and accompanied by large changes in noise and acceleration.
Governor Operation
The electronic governor control system replaces the old centrifugal governor pressure control and is located on the valve body. The control system uses a governor pressure solenoid that can vary pressure, a pressure sensor, and the output shaft speed sensor. The electronic governor control system regulates pressure to control shifts in the first three gears. Output shaft speed and throttle position is used to determine target pressure. Actual governor pressure is read from the sensor and the difference between the target pressure and actual pressure is used to determine duty cycle correction. The duty cycle is the amount of time the governor pressure solenoid needs to be OFF to meet the target pressure. Output shaft speed, throttle position, controller calculations, and shift lever position, all determine different governor pressure curves. Governor pressures can be different at the same output shaft speed. The desired governor pressure is determined by many things; including the acceleration of the vehicle. There is no need for concern if the same output shaft speed has different requested pressures. There is a need for concern if the target pressure and actual pressure are not within three PSI for five seconds or more. If this occurs the control system could result in erratic shifting. The only time the governor control system stays at zero is when the gear selector is in park, neutral, reverse or drive with the vehicle at a stop. When the transmission is in park, neutral, or reverse no line pressure is supplied to the governor pressure solenoid, making governor pressure zero.
Transmission Temperature Sensor
Transmission fluid temperature readings are supplied to the PCM by the trans temp sensor. The temp sensor is located in the governor pressure sensor connector. The temperature readings are used to control engagement of the overdrive clutch, the converter clutch, and governor pressure. Normal resistance value for the thermistor at room temperature is approximately 1000 ohms. The Powertrain Control Module (PCM) prevents engagement of the converter clutch and overdrive clutch, when fluid temperature is below approximately 30 °F. If fluid temperature exceeds 260 °F, the PCM will cause a 4-3 downshift and engage the converter clutch. Engagement is according to the third gear converter clutch engagement schedule.
The overdrive OFF lamp in the instrument panel, also illuminates when the shift back to third occurs. The transmission will not allow fourth gear operation until fluid temperature decreases to approximately 230 °F.
Transmission Output Shaft Speed Sensor
The output shaft speed sensor is located in the overdrive housing. The sensor is positioned over the park gear and monitors transmission output shaft rotating speed. Speed sensor signals are triggered by the park gear lugs as they rotate past the sensor pickup face. One revolution of the output shaft produces 23 pulses. Input signals from the sensor are sent to the PCM for processing.
Torque Converter Electronics
The torque converter contains a converter clutch mechanism, The converter clutch is an electronically controlled mechanism. It is engaged in fourth gear, and in third gear only when the overdrive control switch is in the OFF position, and also, in third gear over temp mode. The torque converter is not a serviceable component. It should be replaced as an assembly when: diagnosis indicates a malfunction has occurred, or when a major malfunction allows debris to enter the converter.
OTHER CONTROLS
Charging System
The charging system is turned ON when the engine is started and ASD relay energized. When the ASD relay is ON, ASD output voltage is supplied to the ASD sense circuit at the PCM. This voltage is connected in some cases, through the PCM and supplied to one of the generator field terminals (Generator Source +). All others, the Generator field is connected directly to the ASD output voltage. The amount of current produced by the generator is controlled by the Electronic Voltage Regulator (EVR) circuitry, in the PCM. Battery temperature is determined either by IAT, Ambient or Battery temperature sensor. This temperature along with sensed line voltage is used by the PCM to vary battery charging. This is accomplished by cycling the path to ground to the other generator field terminal (Generator field driver).
Speed Control
The PCM controls vehicle speed by operation of the speed control servo vacuum and vent solenoids. Energizing the vacuum solenoid applies vacuum to the servo to increase throttle position. Operation of the vent solenoid slowly releases the vacuum allowing throttle position to decrease. A special dump solenoid allows immediate release of throttle position caused by braking, cruise control turn OFF, shifting into neutral, excessive RPM (tires spinning) or ignition key OFF.
DIAGNOSTIC TIPS
During diagnosis, you can compare the LDP solenoid activity with the monitor sequence in Figure 6. If the PCM detects a problem that could set a DTC, the testing is halted and LDP solenoid activity will stop. As each section of the test begins, it indicates that the previous section passed successfully. By watching to see which tests complete, you can see if any conditions are present that the PCM considers abnormal.
For example, if the LDP solenoid is energized for the test cycles to test for blockage (P1486), it means that the LDP has already passed its test for P1494. Then, if the PCM detects a possible blockage, it will set a temporary fault without turning on the MIL and continue the leak portion of the test. However, the PCM will assume that the system is already pressurized and skip the rapid pump cycles.
Always diagnose leaks, if possible, before disconnecting connections. Disconnecting connections may mask a leak condition.
Keep in mind that if the purge solenoid seat is leaking, it could go undetected since the leak would end up in the intake manifold. Disconnect the purge solenoid at the manifold when leak checking. In addition, a pinched hose fault (P1486) could set if the purge solenoid does not purge the fuel system properly (blocked seat). The purge solenoid must vent the fuel system prior to the LDP system test. If the purge solenoid cannot properly vent the system the LDP cannot properly complete the test for P1486 and this fault can be set due to pressure being in the EVAP system during the test sequence.
Multiple actuation's of the DRB III Leak Detection Pump (LDP) Monitor Test can hide a 0.020 leak because of excess vapor generation. Additionally, any source for additional vapor generation can hide a small leak in the EVAP system. Excess vapor generation can delay the fall of the LDP diaphragm thus hiding the small leak. An example of this condition could be bringing a cold vehicle into a warm shop for testing for high ambient temperatures.
Fully plugged and partially plugged underhood vacuum lines have been known to set MIL conditions. P1494 and P0456 can be set for this reason. Always, thoroughly, check plumbing for pinches or blockage before condemning components.