Front Bumper Cover / Fascia: Service and Repair
FASCIA-FRONTREMOVAL
1. Raise and support the vehicle.
2. Remove the three push-pin retainers (1) that secure each front wheel house splash shield (2) to the front fascia assembly (3).
3. Remove the nine screws (1) that secure the belly pan (2) to the underbody.
NOTE: 300 Shown. Magnum and SRT8 similar
4. Remove the screw (5) that secures the front fascia assembly (4) to the nut insert (1) in each front fender.
5. Partially lower the vehicle and remove the push-pin retainers (2) (four-sedan, six-wagon, eight-Charger) that secure the front fascia assembly to the upper radiator support.
6. If equipped, disconnect the headlamp washer system hose from washer reservoir.
7. On all three SRT8 models, disconnect the Tire Pressure Monitoring System connector.
8. Carefully pull the front fascia assembly forward to disengage the push-pin retainer (6) from the slot in each side the fascia and position the fascia to gain access to the fog lamp wire harness connectors (3), if equipped.
Charger
1. Remove the screw (6) that secures the front fascia assembly (5) to the nut insert (1) in each front fender.
2. Partially lower the vehicle and remove the push-pin retainers (4) (four-sedan, six-wagon, eight-Charger) that secure the front fascia assembly to the upper radiator support.
3. Carefully pull the front fascia assembly forward to disengage the push-pin retainer (6) from the slot in each side the fascia and position the fascia to gain access to the fog lamp wire harness connectors (7), if equipped.
9. If equipped, disconnect each fog lamp wire harness connector (1) from the headlamp wire harness (2) and remove the front fascia assembly (3) from the vehicle.
10. If equipped and if required, remove the fog lamps from the front fascia assembly.
11. If required on SRT8 models, remove the lower fascia from the front fascia assembly and discard the metal retaining clips.
12. If required, remove and discard the nut insert (1) from each front fender and remove the push-pin retainer (2).
INSTALLATION
1. If removed, install the push-pin retainer (2) and a new nut insert (1) into each front fender.
NOTE: 300 Shown. Magnum and SRT8 similar.
2. If removed on SRT8 models, install the lower fascia onto the front fascia assembly (4) using new metal retaining clips.
3. If equipped and removed, install the fog lamps onto the front fascia assembly.
4. Position the front fascia assembly to the vehicle and connect each fog lamp wire harness connector (3), if equipped.
5. If equipped, connect the headlamp washer system hose to washer reservoir.
6. On all three SRT8 models, connect the Tire Pressure Monitoring connector.
7. Engage the push-pin retainer (6) into the slot in each side of the front fascia assembly by pushing the fascia rearward.
8. Install the push-pin retainers (2) (four-sedan, six-wagon, eight Charger) that secure the front fascia assembly to the upper radiator support.
9. Raise and support the vehicle.
10. Install the screw (5) that secures the front fascia assembly to the nut insert (1) in each front fender. Tighten the screws securely.
11. Position belly pan to front of vehicle. Install and tighten screws.
Charger
1. Install the screw (6) that secures the front fascia assembly (5) to the nut insert (1) in each front fender.
2. Partially lower the vehicle and install the push-pin retainers (4) (four-sedan, six-wagon, eight-Charger) that secure the front fascia assembly to the upper radiator support.
3. Carefully pull the front fascia assembly rearward to engage the push-pin retainer (6) from the slot in each side the fascia and position the fascia to gain access to the fog lamp wire harness connectors (7), if equipped.
12. Position the belly pan (1) to the front of the vehicle underbody and install the nine screws (1). Tighten the screws securely.
13. Position each front wheel house splash shield (2) to the front fascia assembly (3) and install the push-pin retainers (1).
14. Lower the vehicle.