Electronic Vehicle Information Center - Operation

OPERATION

The Electronic Vehicle Information Center (EVIC) uses both non-switched and ignition switched sources of battery current so that some of its features remain operational at any time, while others may only operate with the ignition switch in the "ON" position. When the ignition switch is turned to the "ON" position, the EVIC display will return to the last function being displayed before the ignition was turned to the "OFF" position.

The EVIC system is comprised of several different components that communicate over the Controller Area Network (CAN) and Local Interface Network (LIN) Data Buses. If the system is inoperative a scan tool and the appropriate diagnostic information must be used to diagnose the system.

The EVIC function buttons are used to operate the different functions of the EVIC system. Pressing and releasing the MENU button allows the driver to select the Compass/Temperature, Trip Computer, Personal Settings or System Status functions. The STEP button is used to toggle through options or features of the Trip Computer, Personal Settings or System Status functions. Pressing and releasing the RESET button allows the selection of setting or resetting of the function currently displayed at that time. Pressing and releasing the C/T (compass/temperature) button will cause the EVIC to return to the compass/temperature display mode from any other mode.

EVIC DISPLAY MODES

SYSTEM STATUS MODE

System display mode displays warnings and user interaction messages on the EVIC display. The driver can scroll to view multiple messages by using the STEP button.

When the appropriate conditions exist, the EVIC displays the following messages:

- Turn Signal On (with a continuous warning chime if the vehicle is driven more than 1 mile [1.6 km] with either turn signal on)
- Left Front Turn Signal Lamp Out (with a single chime)
- Left Rear Turn Signal Lamp Out (with a single chime)
- Right Front Turn Signal Lamp Out (with a single chime)
- Right Rear Turn Signal Lamp Out (with a single chime)
- Remote Keyless Entry (RKE) Battery Low (with a single chime)
- Low Fuel
- Cal (if equipped with a compass module)
- Oil Change Required (with a single chime)
- Low Washer Fluid
- Coolant Low
- Key in Ignition
- Lights On

PERSONAL SETTINGS MODE (CUSTOMER PROGRAMMABLE FEATURES)

Allows the driver to set and recall features when the transmission is in Park by pressing and releasing the MENU button until Personal Settings is displayed in the EVIC. Pressing and releasing the STEP button will scroll through the following personal settings choices:

- Fuel saver indicator, Economizer (ECO / ECO-on) When the fuel saver indicator ON is selected, the ECO indicator will display below the outside temperature in the EVIC display. This message will display whenever the vehicle is driver in a fuel efficient manner.
- Language When in this display you may select one of three languages for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the RESET button while in this display to select English, Espanol, or Francois. Then, as you continue, the information will display in the selected language. NOTE: The EVIC will not change the U Connect(TM) language selection.

- Unlock Doors Automatically on Exit When ON is selected, all doors will unlock when the vehicle is stopped and the transmission is in the P (Park) or N (Neutral) position and the driver's door is opened. To make your selection, press and release the RESET button until "ON" or "OFF" appears.
- Remote Key Unlock When DRIVER DOOR 1ST PRESS is selected, only the driver's door will unlock on the first press of the remote keyless entry unlock button. When Driver Door 1st Press is selected, you must press of the remote keyless entry unlock button twice to unlock the passenger's doors. When ALL DOORS 1ST PRESS is selected, all of the doors will unlock on the first press of the remote keyless entry unlock button. To make your selection, press and release the RESET button until "Driver Door 1st Press" or "All Doors 1st Press" appears.
- Sound Horn with Remote Key Lock When ON is selected, a short horn sound will occur when the remote keyless entry "Lock" button is pressed. This feature may be selected with or without the flash lights on lock/unlock feature. To make your selection, press and release the RESET button until "ON" or "OFF" appears.
- Flash Lights with Remote Key Lock When ON is selected, the front and rear turn signals will flash when the doors are locked or unlocked with the remote keyless entry transmitter. This feature may be selected with or without the sound horn on lock feature selected. To make your selection, press and release the RESET button until "ON" or "OFF" appears.
- Delay Turning Headlights Off When this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. To make your selection, press and release the RESET button until "0," "30," "60," or "90" appears.
- Headlights On with Wipers (Available with Auto Headlights Only) When this feature is selected and the headlight switch is in the AUTO position, the headlights will activate approximately 10 seconds after the wipers are turned on. To make your selection, press and release the RESET button until "ON" or "OFF" appears.
- Delay Power Off to Accessories Until Exit When this feature is selected, the power window switches, radio, hands-free system (if equipped), DVD video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned off. Opening a vehicle door will cancel this feature. To make your selection, press and release the RESET button until "Off," "45 sec.," "5 min.," or "10 min." appears.
- Confirmation of Voice Commands - If Equipped When ON is selected, all voice commands from the U Connect(TM) system are confirmed. To make your selection, press and release the RESET button until "ON" or "OFF" appears.
- Display Units of Measure in The EVIC, trip odometer, and navigation system (if equipped) can be changed between English and Metric units of measure. To make your selection, press and release the RESET button until "US" or "METRIC" appears.

COMPASS/TEMPERATURE

Compass heading and outside temperature are displayed on the EVIC display screen. One of eight compass headings to indicate the direction the vehicle is facing (N, S, E, W, NE, NW, SE, SW) and one of 15 compass variance settings can be programmed. Outside temperature is displayed in °C (degrees Celsius) or °F (degrees Fahrenheit).

For additional information regarding the compass, refer to Personal Settings (Customer Programmable Features).

NOTE: Vehicles equipped with a NAV radio, the compass feature is an integral part of the NAV system. Audio and Video - Operation for more information.

TRIP COMPUTER

Press and release the MENU button until one of the following Trip Functions displays in the EVIC:

- Average Fuel Economy
- Distance To Empty
- Elapsed Time
- Display Units of Measure in

Press the STEP button to cycle through all the Trip Computer functions.

The Trip Functions mode displays the following information:

- Average Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read "RESET" or show dashes for two seconds. Then, the history information will be erased, and the averaging will continue from the last fuel average reading before the reset.
- Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the RESET button. When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a text display of "LOW FUEL." This display will continue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the "LOW FUEL" text and a new DTE value will display.
- Elapsed Time Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed time will increment when the ignition switch is in the ON or START position.
- Display Units of Measure in: To make your selection, press and release the RESET button until "US" or "METRIC" appears.
To Reset The Display Reset will only occur while a reset table function is being displayed. Press and release the RESET button once to clear the reset table function being displayed. To reset all reset table functions, press and release the RESET button a second time within 3 seconds of resetting the currently displayed function (>Reset ALL will display during this 3 second window).