Instrument Panel Pad - Installation
INSTALLATION
1. With the help of an assistant, position the instrument panel pad near the structure.
2. Connect the pin switch harness connectors (1, 2) located behind the upper right corner of the glove box cavity.
CAUTION: Make sure that wiring harnesses are routed to the appropriate opening and are not pinched.
3. Continue to align and position the I/P pad onto the structure.
4. Lower the PAB studs into the bracket located on the structure. Make sure there is no interference between the bracket (2) and the PAB.
5. Install the I/P cover over the tab located on the side by pulling the side of the cover out and forward. Repeat on the opposite side.
6. Push forward on the I/P cover to engage the snap retainers located around the glove box cavity and lower steering column area.
7. Install the I/P pad fence nut (1) located across the top of the pad near the windshield. Tighten the nuts securely. Repeat for the opposite side.
8. Connect and install the I/P speakers (2), . Instrument Panel
9. Install the nine I/P cover to defroster duct center trim panel fence screws (1). Tighten the screws securely.
10. Install the two I/P pad to structure bolts (1) located below the steering column. Tighten the bolts securely.
NOTE: View shown is looking from under the glove box opening.
11. Install the I/P pad to structure fasteners (1) located near the glove box striker just under the top of the glove box opening. Tighten the fasteners securely.
12. Install the fasteners securing the PAB to the structure, Passenger Air Bag - Installation.
13. Connect the squib connectors to the passenger side airbag.
14. Install the I/P pad to structure bolts (1) located on the lower edge of the glove box opening. Tighten the bolts securely.
15. Install the two I/P pad to structure bolts (1) located on the side. Tighten the bolts securely. Repeat on the opposite side.
16. Install the two screws located at the top of center stack. Tighten the screws securely.
17. Install the I/P pad to structure bolts (1) located in the middle of the center stack cavity. Tighten the bolts securely.
18. Tighten the I/P pad to structure bolt (1) located in the instrument cluster cavity. Tighten the bolt securely.
19. Install the instrument cluster (1), Instrument Cluster - Installation.
20. Attach the foam blocks (2) located just below the instrument cluster (1).
21. Access and connect the headlamp/dimmer switch harness connectors through the outlet vent/trim opening.
22. Install the instrument panel outlet vent/trim (1), Air Outlet - Installation.
23. Connect the lower I/P courtesy lamp/LED, Courtesy Lamp - Installation.
24. Connect and attach the 12V power outlet harness.
25. Install and connect the storage bin (1) from the instrument panel.
26. Position the floor console (1) into the vehicle.
27. Engage the floor console (1) front snap retainers into the lower storage bin (2).
28. Connect the auxiliary/USB harness (1) located forward of the shifter.
29. Disconnect the vehicle harness (1) located near the shifter.
30. Install the four bolts (1) located in the console storage bin. Tighten the bolts securely.
31. Connect and install the shifter bezel (1). Make sure all snap retainers are properly seated.
32. Install the bin liner and coin holder inside the console bin.
33. Close the console lid.
34. Install the shifter knob (1).
35. Install the gap hider trim panel (2) located above the front storage bin (1). Make sure all snap retainers are properly seated.
36. Connect the antenna(s) (2), RF HUB and UCI cables (4), video cable (3) and wiring connectors (2) to the Telematics Gateway Module (TGM).
37. Position the TGM into the mounting location.
38. Install the retainers (1) to the TGM.
CAUTION: Do not disconnect/connect the ICSS/switch bank without referring to the appropriate procedure. The harness connector is very fragile and could be damaged if not properly removed/installed.
39. Connect the integrated center stack screen,. Integrated Center Stack Screen Module - Installation
40. Align and push forward to engage the snap retainers securing the center trim bezel (1) to the I/P.
41. Install the two fasteners (2) securing the center trim bezel (1) to the I/P.
42. Position the switch-bank assembly in place.
43. Connect the electrical connector (2) to the back of the switch-bank assembly (1).
44. Position the switch-bank in the I/P and press evenly the engage the two lower clips (3).
45. Install, and tighten the two screws (2) that secure the switch-bank (1) to the I/P (4).
46. Install the instrument panel trim (1) located left of the center stack bezel.
47. Install the instrument panel outlet vent/trim (1), Air Outlet - Installation.
48. Install the glove box (1).
49. Position and install the defroster grille (1) from the instrument panel. Make sure all the snap retainers are properly seated.
NOTE: Left side shown. Right side similar.
50. Connect the electrical connectors located at the left and right A-pillar.
51. Install the A-pillar trim panels, A-Pillar Trim Panel - Installation.
52. Install the lower cowl panel (1).
53. Install the door scuff plate (2).
54. Install the steering column as an assembly, Steering Column - Installation.
55. Install the upper and lower steering column shrouds (1, 2).
56. Install the fasteners (1, 2, 5) securing the lower and upper steering column shrouds. Tighten the fasteners securely.
57. If equipped, install the knee blocker airbag, Knee Blocker Air Bag - Installation.
58. Position the lower steering column and connect the harness (1) to the aspirator (2).
59. Install the lower steering column panel (1). Make sure all snap retainers are properly seated.
60. Position the hush/silencer panel (2).
61. Install the fasteners (1) from the hush/silencer panel (2) located under the glove box area.
62. Position the close out panel (3).
63. Install the fasteners (1, 2) to the close out panel (3) located under the left hand side of the instrument panel.
NOTE: LHD model shown in illustrations. RHD model similar.
64. Install the instrument panel end cap. Repeat on opposite side.
65. Connect the negative battery cable.