Part 2
DISASSEMBLY
47. Remove the output transfer gear retaining strap (3).
48. Install the (9739) (2) onto the output transfer gear (3).
49. Remove the output transfer gear bolt (1).
50. Grind the staked tabs (1) from the transfer gear (underdrive compounder side).
51. Install the (9739) (1) onto the transfer gear (underdrive compounder side) and remove the nut.
52. Lift the transfer gear from the underdrive compounder shaft.
53. Using (L-4407A) (1) and (6055) (3) remove output shaft transfer gear (2) and select shim.
54. Using (5048) with (5048-5) and (L-4539-2) (1) remove output gear bearing cone.
55. Using (C-293-PA) (1), (9738) (3) and (9678) remove compounder transfer gear bearing cone.
56. Remove rear carrier assembly (1) from transaxle (2).
57. Remove rear carrier assembly (3) bearing cone using (5048) with (5048-3) and (6055).
58. Install spring (6057) (1), (5059-A) (2) and (5058A-3) (3).
59. Compress low/reverse spring using (5059-A) (4).
60. Remove snap ring (1) at low/reverse piston return spring.
61. Remove low/reverse spring compressor tool and low reverse piston return spring (1).
NOTE: The Low/Reverse Clutch Piston has bonded seals which are not individually serviceable. Seal replacement requires replacement of the piston assembly.
62. Remove low/reverse clutch piston (1).
63. Remove low/reverse piston retainer-to-case screws (3).
64. Remove low/reverse piston retainer (1).
65. Remove low/reverse piston retainer-to-case gasket (2), gasket holes must line up (1).
66. Using a hammer and suitable drift (2), drive out inner output bearing cup (1).
67. Using (6062A) (1), remove outer output bearing cup (2).
68. Remove the snap ring (1) at the underdrive compounder assembly (2).
69. Remove four bolts (1) at the compounder bearing retainer.
70. Install (9908) (2) to the compounder bearing retainer.
71. Install (C-3752) (1) to (9908) (2) and pull the underdrive compounder assembly from the case.
NOTE: Insure that the planetary gear set / output hub is removed as part of the underdrive compounder assembly.
72. Remove the underdrive compounder assembly (2).
73. Remove the bolts (1) at the remote pinion cover (2).
74. Remove the remote pinion (1) and the remote pinion cover (2) from the case.
75. Remove the remote pinion cover (1) from the remote pinion (2).
76. Using (8913) (2) and (9738)(3) and (8915) (1) remove the remote pinion cover bearing cup (4) and selective shim.
77. Using (8912) and (8915) (1, 2) pull remote pinion small bearing cup (3) from the case.
78. Remove the differential output bearing cover bolts (1).
79. Remove differential output bearing cover (2).
80. Remove the differential cover bolts (1).
81. Remove the differential cover (1).
82. Remove the out seal (2), oil singer (3) and the small bearing cup (4).
83. Remove the large bearing cup.
84. Remove the differential.
85. Remove the manual lever and TRS Transmission Range Sensor - Removal.
86. Remove the set screw (1) for the park pawl shaft.
87. Remove the snap ring (1) for the park guide assembly (2).
88. Remove the park guide assembly (1).
89. Remove the plug (1) to allow the park pawl shaft to be removed.
90. Slide the shaft (1) out of the park pawl (3).
91. Remove the park pawl shaft (1).
92. Remove the park pawl (1) and the park pawl spring (2).