B1D32-11

B1D32-11-DRIVER MIRROR HEATER CONTROL - CIRCUIT SHORT TO GROUND





For a complete wiring diagram, refer to the Wiring Information.

- When Monitored:
Continuously.

- Set Condition:
The Door Module senses a short low on the (C16) Driver Mirror Heater Driver circuit for more than two seconds with the heater switched on.





1. TEST FOR INTERMITTENT CONDITION
1. Turn the ignition on.
2. Using a scan tool, record and erase Diagnostic Trouble Codes (DTCs).
3. Turn the turn signal on, if equipped with turn signal mirror.
4. Turn the puddle lamps on, if equipped with puddle lamp mirror.
5. Turn the rear defogger on.
6. Press and release the Mirror Select switch to select the Driver Outside Rearview Mirror.
7. Operate the Mirror Adjust switch in all directions several times while monitoring the scan tool for DTCs. NOTE: After adjusting the mirror in one direction wait at least two seconds before adjusting the mirror in the opposite direction, as this will allow time for an active fault to set if present.

Is the DTC active?

Yes

- Go To 2

No

- The conditions that caused this code to set are not present at this time. For vehicle's equipped with folding outside rearview mirrors, repeat test with mirror folded. If DTC is now active, Go To 2. Otherwise, use the wiring diagram/schematic as a guide and inspect the wiring and connectors.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

2. CHECK (C16) DRIVER MIRROR HEATER DRIVER CIRCUIT FOR A SHORT TO GROUND




1. Turn the ignition off.
2. Disconnect the Driver Outside Rearview Mirror C2 (Component Side) connector from the Door Module C2 connector.
3. Measure the resistance of the (C16) Driver Mirror Heater Driver circuit between ground and the Driver Outside Rearview Mirror C2 (Component Side) connector.

Is the resistance below 10K Ohms?

Yes

- Repair the (C16) Driver Mirror Heater Driver circuit for a short to ground. If the wiring harness and connector are okay, replace the Driver Outside Rearview Mirror.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Go To 3

3. CHECK (C16) DRIVER MIRROR HEATER DRIVER CIRCUIT FOR A SHORT TO (P75) DRIVER MIRROR HORIZONTAL DRIVER CIRCUIT, (P71) DRIVER MIRROR VERTICAL DRIVER CIRCUIT, OR TO (P73) DRIVER MIRROR COMMON DRIVER CIRCUIT




1. Measure the resistance between the (C16) Driver Mirror Heater Driver circuit and the (P75) Driver Mirror Horizontal Driver circuit at the Driver Outside Rearview Mirror C2 (Component Side) connector.
2. Measure the resistance between the (C16) Driver Mirror Heater Driver circuit and the (P71) Driver Mirror Vertical Driver circuit at the Driver Outside Rearview Mirror C2 (Component Side) connector.
3. Measure the resistance between the (C16) Driver Mirror Heater Driver circuit and the (P73) Driver Mirror Common Driver circuit at the Driver Outside Rearview Mirror C2 (Component Side) connector.

Is the resistance below 10K Ohms for any measurement?

Yes

- Repair all circuits with a resistance below 10K Ohms for a short to the (C16) Driver Mirror Heater Driver circuit. If the wiring harness and connector are okay, replace the Driver Outside Rearview Mirror.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No, with Turn Signal Mirror

- Go To 4

No, without Turn Signal Mirror

- Go To 5

4. CHECK (C16) DRIVER MIRROR HEATER DRIVER CIRCUIT FOR A SHORT TO (P593) DRIVER MIRROR TURN SIGNAL RETURN CIRCUIT




1. Measure the resistance between the (C16) Driver Mirror Heater Driver circuit and the (P593) Driver Mirror Turn Signal Return circuit at the Driver Outside Rearview Mirror C2 (Component Side) connector.

Is the resistance below 10K Ohms?

Yes

- Repair the (C16) Driver Mirror Heater Driver circuit for a short to the (P593) Driver Mirror Turn Signal Return circuit. If the wiring harness and connector are okay, replace the Driver Outside Rearview Mirror.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Go To 5

5. CHECK (C16) DRIVER MIRROR HEATER DRIVER CIRCUIT FOR A SHORT TO (C160) DRIVER MIRROR HEATER RETURN CIRCUIT




1. Measure the resistance between the (C16) Driver Mirror Heater Driver circuit and the (C160) Driver Mirror Heater Return circuit at the Driver Outside Rearview Mirror C2 (Component Side) connector.

Is the resistance below 1.0 Ohm?

Yes

- Repair the (C16) Driver Mirror Heater Driver circuit for a short to the (C160) Driver Mirror Heater Return circuit. If the wiring harness and connector are okay, replace the Driver Outside Rearview Mirror.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Go To 6

6. CHECK (C16) DRIVER MIRROR HEATER DRIVER CIRCUIT FOR A SHORT TO (69) DRIVER MIRROR SENSOR GROUND CIRCUIT




1. Disconnect the Driver Outside Rearview Mirror C1 (Component Side) connector from the Door Module C1 connector.
2. Measure the resistance between the (C16) Driver Mirror Heater Driver circuit and the (P69) Driver Mirror Sensor Ground circuit at the Driver Outside Rearview Mirror C2 and C1 (Component Side) connectors.

Is the resistance below 10K Ohms?

Yes

- Repair the (C16) Driver Mirror Heater Driver circuit for a short to the (P69) Driver Mirror Sensor Ground circuit. If the wiring harness and connector are okay, replace the Driver Outside Rearview Mirror.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No, with Puddle Lamp Mirror

- Go To 7

No, without Puddle Lamp Mirror

- Inspect the wiring and connectors for damage and repair as necessary. If the wiring and connectors are okay, replace the Door Module.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

7. CHECK (C16) DRIVER MIRROR HEATER DRIVER CIRCUIT FOR A SHORT TO (P591) DRIVER PUDDLE LAMP RETURN CIRCUIT




1. Measure the resistance between the (C16) Driver Mirror Heater Driver circuit and the (P591) Driver Puddle Lamp Return circuit at the Driver Outside Rearview Mirror C2 and C1 (Component Side) connectors.

Is the resistance below 10K Ohms?

Yes

- Repair the (C16) Driver Mirror Heater Driver circuit for a short to the (P591) Driver Puddle Lamp Return circuit. If the wiring harness and connector are okay, replace the Driver Outside Rearview Mirror.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Inspect the wiring and connectors for damage and repair as necessary. If the wiring and connectors are okay, replace the Door Module.
- Perform the BODY VERIFICATION TEST. Body Verification Test.