Operation CHARM: Car repair manuals for everyone.

A/T - AOD Harsh/Rough Shifts


91ford19

Article No.
91-11-14

05/30/91


TRANSMISSION - AUTOMATIC - AOD - HARSH/ROUGH 3-4/4-3 SHIFTS


FORD: 1989-90 CROWN VICTORIA, MUSTANG, THUNDERBIRD

LINCOLN-MERCURY: 1989-90 COUGAR, GRAND MARQUIS, MARK VII, TOWN CAR

LIGHT TRUCK: 1989-90 BRONCO, E-150, F-150


ISSUE: Harsh or rough transmission shifts in certain vehicles may be calibration characteristics of the AOD transmission split torque feature. However some customer transmission shifting concerns could be the result of improper (TV) pressure or sticking control valves.

ACTION: Diagnose and repair the transmission. Using the following procedures which have proven to be an effective sequence of repair and significantly reduces the potential for unnecessary replacement of major components.


Before performing any transmission repairs, test drive the vehicle to verify the 3-4 shift concern. Some of these concerns may be related to "tip-out" clunk due to an engine processor strategy and may be repaired as specified in TSB 90-17-4.

If the referenced TSB does not eliminate the concern, refer to the following repair procedure.


Diagnose and Adjust (TV) pressure.

Refer to Section 17 of the appropriate Car or Truck Shop Manual for service details in performing the following adjustment.

1. Check throttle valve (TV) pressure and verify 33-34 PSI for passenger vehicles and 29-30 PSI for trucks. If TV pressure is not as specified, adjust TV pressure as outlined in the appropriate Car or Truck Shop Manual.

2. With TV pressure properly set, test drive the vehicle to verify if symptom still exists.

If the vehicle has not been corrected, proceed as follows:

Inspect and Clean Main Control

Refer to Section 17 of the appropriate Car or Truck Shop Manual for service details in performing the following repair.

1. Throughly drain the transmission and converter.

2. Remove the oil pan and main control assembly.


3. Disassemble the main control and check for stuck valves. With the separating plate removed, check each valve for free movement, pay special attention to the 2-3 capacity modulator, 2-3 TV modulator, and the 3-4 TV modulator valve. Using crocus cloth, clean and polish lands as required and reassemble.

4. Install new upper and lower main control gaskets.

5. Torque main control attaching bolts to 85 in.lbs. +/- 5 in.lbs.

NOTE: Target 85 in.lbs.

6. Install oil pan using a new pan gasket and fill with Mercon/R transmission fluid to the proper level.

7. Recheck TV pressure and re-adjust as required to establish 33-34 PSI for passenger cars and 29-30 PSI for trucks.

8. Test drive to verify repair.

As indicated, the above repair procedure has proven to be effective with over 90% of the 3-4/4-3 shift concerns. However, in some circumstances, the above procedure may not completely satisfy the customer concerns. In those instances, the 1991 Main Control may provide the required shift improvements. Refer to the following AOD Main Control Complexity Chart for the 1989-1990 Main Controls and their equivalent 1991 replacements.


AOD MAIN CONTROL COMPLEXITY CHART

ADD SERVICE MAIN DELETE
PART CONTROL SERVICE
NUMBER I.D. PART NUMBER MAIN CONTROL I.D.

F1TZ-7A100-C GNO F0TZ-7A100-G DOA, MPA
E9TZ-7A100-J MRA
F1TZ-7A100-B GNN F0TZ-7A100-F DOX, MPX
E9TZ-7A100-H MRX
F1AZ-7A100-D JNF E9AZ-7A100-B COH, VPH, VRH
RRH
F1SZ-7A100-B BNJ E9SZ-7A100-B URL, URY, SRY
F0SZ-7A100-B GPJ, UPJ
F1AZ-7A100-E JFK
F0AZ-7A100-D CJH
E9AZ-7A100-G VGH, RGH, WFR
E5AZ-7A100-D BER, OER, ODR
F1LY-7A100-A DNX
F0LY-7A100-B BOC, BOX, PPC
E9LY-7A100-A PRX
E9LY-7A100-B PRC
F1SZ-7A100-A ANV F0SZ-7A100-A TPM
E9SZ-7A100-D TRM, TRF

PART NUMBER PART NAME CLASS

D9AZ-7D100-B Gasket Lower Control C
E9SZ-7C155-A Gasket Upper Control B
E0AZ-7A191-B Gasket Transmission Pan AM
XT-2-QDX Mercon/R Fluid VG

OTHER APPLICABLE ARTICLES: 91-5-5
WARRANTY STATUS: Eligible Under Basic Warranty
Coverage
OPERATION DESCRIPTION TIME
911114A Adjust TV Pressure 0.7 Hrs
911114B Inspect And Clean Control 2.6 Hrs
Valves
911114C Replace Main Control Valve 1.3 Hrs
DEALER CODING
BASIC PART NO. CONDITION CODE
7A100 09
OASIS CODES: 501000, 502000, 504000