Instrument Panel

Instrument Panel

Removal

All vehicles

1. If equipped, remove the floor console. For additional information, refer to Console - Floor Console - Floor.

2. Remove and discard the upper steering column shaft-to-steering column bolt.





3. Remove the steering wheel. For additional information, refer to Steering Column.

4. Detach the upper steering column shaft from the steering column.

Vehicles with a manual transmission

5. Remove the shift lever and boot. For additional information, refer to Manual Transmission/Transaxle.

All vehicles

6. Remove the RH and LH A-pillar trim panels and the RH and LH lower cowl trim panels.

7. Position aside the RH and LH front door weatherstrips.

8. Remove the RH and LH instrument panel side trim panels.

9. Remove the parking brake release handle bolt and position aside the parking brake release handle.

10. Remove the steering column opening trim panel.
- Pull the steering column opening trim panel outward to release the steering column opening trim panel retaining clips.

Vehicles with an automatic transmission

11. Remove the selector lever cable from the steering column.
- Disconnect the selector lever cable from the steering column selector lever.

- Remove the selector lever cable from the steering column bracket.





All vehicles

12. Disconnect the 3 wiring harness electrical connectors located under the steering column opening panel.





13. If equipped, disconnect the satellite radio antenna connector located under the steering column opening panel.





14. Remove the RH lower insulator panel.
- Remove the 2 pushpin retainers.





15. Disconnect the antenna cable and the bulkhead electrical connector.





16. Disconnect the bulkhead electrical connector and the 2 connectors from the Smart Junction Box (SJB).





17. Lower the glove compartment.

1. Open the glove compartment.

2. Depress the glove compartment stop and lower the glove compartment.





18. Disconnect the 2 electrical connectors that are attached to the plenum chamber.





19. Close the glove compartment.

1. Depress the glove compartment stop and raise the glove compartment.

2. Close the glove compartment.





20. Remove the lower instrument panel center support bolt.





21. Remove the instrument panel upper cowl bolt covers.

22. Remove the 3 instrument panel upper cowl bolts.

23. Remove the LH door weather shield.
- Remove the 4 LH door weather shield pin-type retainers.





24. Remove the LH instrument panel side bolt cover.





25. NOTICE: Place tape on the LH front door as shown to avoid damage to the paint.

Place tape on the LH front door.





26. Remove the LH instrument panel side bolt.

27. Remove the RH and LH instrument panel bolts.

28. NOTICE: To avoid damage to the instrument panel, an assistant is required when carrying out this step.

NOTE: Make sure that all electrical connectors and wiring are not hindered before removing the instrument panel.

Remove the instrument panel.

Installation

All vehicles

1. NOTICE: To avoid damage to the instrument panel, an assistant is required when carrying out this step.

NOTE: Make sure that all electrical connectors and wiring are correctly routed when installing the instrument panel.

Install the instrument panel.

2. Install the RH and LH instrument panel bolts.
- Tighten to 40 Nm (30 lb-ft).

3. NOTE: Use LH instrument panel side bolt guide to prevent the LH instrument panel side bolt from falling into the lower cowl panel.

Install the LH instrument panel side bolt.

- Install the LH instrument panel side bolt guide (part number 54021A08) into the LH instrument panel side bolt opening.

- Install the LH instrument panel side bolt into the LH instrument panel.
- Tighten to 40 Nm (30 lb-ft).

4. Remove the tape from the LH front door.





5. Install the LH instrument panel side bolt cover.





6. Install the LH door weather shield.
- Install the 4 LH door weather shield pin-type retainers.





7. Install the 3 instrument panel upper cowl bolts.
- Tighten to 40 Nm (30 lb-ft).

8. Install the instrument panel upper cowl bolt covers.

9. Install the lower instrument panel center support bolt.
- Tighten to 40 Nm (30 lb-ft).





10. Lower the glove compartment.

1. Open the glove compartment.

2. Depress the glove compartment stop and lower the glove compartment.





11. Connect the 2 electrical connectors that are attached to the plenum chamber.





12. Close the glove compartment.

1. Depress the glove compartment stop and raise the glove compartment.

2. Close the glove compartment.





13. Connect the bulkhead electrical connector and the 2 connectors to the SJB.





14. Connect the antenna cable and the bulkhead electrical connector.





15. Install the RH lower insulator panel.
- Install the 2 pushpin retainers.





16. Connect the 3 wiring harness electrical connectors located under the steering column opening panel.





17. If equipped, connect the satellite radio antenna connector located under the steering column opening panel.





Vehicles with an automatic transmission

18. Install the selector lever cable to the steering column.
- Connect the selector lever cable to the steering column selector lever.

- Install the selector lever cable to the steering column bracket.





All vehicles

19. Install the steering column opening trim panel.
- Make sure to align the trim panel retaining clips to the adjacent retaining clip holes.

20. Install the parking brake release handle and bolt.
- Tighten to 10 Nm (89 lb-in).

21. Install the RH and LH instrument panel side trim panels.
- Make sure to align the trim panel retaining clips to the adjacent retaining clip holes.

22. Install the RH and LH A-pillar trim panels and the RH and LH lower cowl trim panels.

23. Install the RH and LH front door weatherstrips.

Vehicles with a manual transmission

24. Install the shift lever and boot. For additional information, refer to Manual Transmission/Transaxle.

All vehicles

25. Install the upper steering column shaft to the steering column.

26. Install the steering wheel. For additional information, refer to Steering Column.

27. Install a new upper steering column shaft-to-steering column bolt.
- Tighten to 28 Nm (21 lb-ft).





28. If equipped, install the floor console. For additional information, refer to Console - Floor Console - Floor.