P1735

DTC P1735: Problem in Shift Control System:
^ Shift Solenoid Valves B and C Stuck OFF
^ Shift Solenoid Valve E Stuck ON
^ Shift Valves B, C, and E Stuck
^ A/T Clutch Pressure Control Solenoid Valve A Stuck OFF

NOTE: Record all freeze data and review General Troubleshooting Information before you troubleshoot.

1. Warm up the engine to normal operating temperature (the radiator fan comes on).
2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.
3. Drain the ATF through a strainer. Inspect the strainer for metal debris or excessive clutch material.
Does the strainer contain metal debris or excessive clutch material?
YES-Replace the transmission.
NO-Replace the ATF, then go to step 4.
4. Clear the DTC with the HDS.
5. Test-drive the vehicle in the D position through all four gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.
6. Retest-drive the vehicle in the D position through all four gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.
7. Check the OBD status in DTC Monitor Tool from DTCs/Freeze Data in A/T Mode Menu for a pass/fail test of code P1735.
Did the result indicate a fail?
YES-Go to step 8.
NO-Intermittent failure, the system is OK at this time. If the tester indicates NOT COMPLETE, return to step 5 and recheck.
8. Clear the DTC with the HDS.
9. Select Shift Solenoid B in Miscellaneous Test Menu, and check that the shift solenoid valve B operates with the HDS.
Is a clicking sound heard?
YES-Go to step 10.
NO-Replace shift solenoid valve B, then go to step 17.
10. Select Clutch Pressure Control (Linear) Solenoid C in Miscellaneous Test Menu, and test the A/T clutch pressure control solenoid valve C with the HDS.
Is a clicking sound heard?
YES-Go to step 11.
NO-Replace shift solenoid valve C, then go to step 17.
11. Select Shift Solenoid E in Miscellaneous Test Menu, and check that the shift solenoid valve E operates with the HDS.
Is a clicking sound heard?
YES-Go to step 12.
NO-Replace shift solenoid valve E, then go to step 17.
12. Select Clutch Pressure Control (Linear) Solenoid A in Miscellaneous Test Menu, and test the A/T clutch pressure control solenoid valve A with the HDS.
Is the system OK?
YES-Intermittent failure, the system is OK at this time. If the tester indicates NOT COMPLETE, return to step 12 and recheck.
NO-Follow instructions indicated on the HDS by the test result, but if the tester has not determined the cause of the failure, go to step 13. If any part was replaced, go to step 17.
13. Inspect A/T clutch pressure control solenoid valve A.
Does the A/T clutch pressure control solenoid valve A work properly?
YES-Repair hydraulic system related with shift valve E, or replace the transmission, then go to step 12.
NO-Replace A/T clutch pressure control solenoid valve A, then go to step 12.
14. Test-drive the vehicle in the D position through all four gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.
15. Retest-drive the vehicle in the D position through all four gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.
16. Check the OBD status in DTC Monitor Tool from DTCs/Freeze Data in A/T Mode Menu for a pass/fail test of code P1735
Did the result indicate a fail?
YES-Repair hydraulic system related with shift valves B, C, and E, or replace the transmission, then go to step 17.
NO-Intermittent failure, the system is OK at this time. If the tester indicates NOT COMPLETE, return to step 14 and recheck.
17. Clear the DTC with the HDS.
18. Test-drive the vehicle in the D position through all four gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.
19. Retest-drive the vehicle in the D position through all four gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.
20. Check the OBD status in DTC Monitor Tool from DTCs/Freeze Data in A/T Mode Menu for a pass/fail test of code P1735.
Did the result indicate a pass?
YES-The problem has been corrected.
NO-Return to step 8 and recheck.