Operation CHARM: Car repair manuals for everyone.
Home >> Honda >> 2007 >> Odyssey V6-3.5L >> Repair and Diagnosis >> Accessories and Optional Equipment >> Antitheft and Alarm Systems >> Testing and Inspection >> Component Tests and General Diagnostics >> Keyless/Power Door Locks/Security System >> Control Unit Input Test

Control Unit Input Test

Control Unit Input Test

NOTE: Before troubleshooting the keyless entry/security control system, troubleshoot the multiplex integrated control system first using B-CAN System Diagnosis Test Mode A.

Make sure the ignition switch OFF before troubleshooting the driver's under-dash fuse/relay box.

Multiplex Integrated Control Unit

1. Turn the ignition switch OFF.
2. Remove the left kick panel.




3. Disconnect the driver's under-dash fuse/relay box connectors.

NOTE: All connector views are wire side of female terminals.

4. Inspect the connector and socket terminals to be sure they are all making good contact.
- If the terminals are bent, loose or corroded, repair them as necessary, and recheck the system.
- If the terminals look OK, go to step 5.




5. With the connectors still disconnected, make these input tests at the connectors.
- If any test indicates a problem, find and correct the cause, then recheck the system.
- If the input tests prove OK, go to step 6.







6. Reconnect all connectors to the driver's under-dash fuse/relay box. Turn the ignition switch ON (II), and make these input tests at the appropriate connectors on the driver's under-dash fuse/relay box.
- If any test indicates a problem, find and correct the cause, then recheck the system.
- If all the input tests prove OK, go to step 7.

MICU-Rear Junction Box Control Unit

7. Turn the ignition switch OFF.
8. Remove the right rear trim.




9. Disconnect the MICU-rear junction box connectors A, B, C and F.

NOTE: All connector views are wire side of female terminals.

10. Inspect the connector and socket terminals to be sure they are all making good contact.
- if the terminals are bent, loose or corroded, repair them as necessary and recheck the system.
- If the terminals look OK, go to step 1.




11. With the connectors still disconnected, make these input tests at the connectors.
- If any test indicates a problem, find and correct the cause, then recheck the system.
- If all the input tests prove OK, go to step 12.




12. Reconnect all connectors to the MICU-rear junction box. Turn the ignition switch ON (II), and make these input tests at the appropriate connectors on the MICU-rear junction box.
- If any test indicates a problem, find and correct the cause, then recheck the system.
- If all the input tests prove OK, go to step 13.

Relay Control Module

13. Turn the ignition switch OFF.
14. Remove the under-hood fuse/relay box.




15. Remove the under cover from the under-hood fuse/relay box, and disconnect the connector H (18P).
16. Inspect the connector and socket terminals to be sure they are all making good contact.
- If the terminals are bent, loose or corroded, repair them as necessary and recheck the system.
- If the terminals look OK, go to step 17.




17. With the connector still disconnected, make these input tests at the connectors.
- If any test indicates a problem, find and correct the cause, then recheck the system.
- If all the input tests prove OK, go to step 18.




18. Reconnect the connector to the under-hood fuse/relay box, turn the ignition switch ON (II) and make the input test at the appropriate connector on the under-hood fuse/relay box.
- If a test indicates a problem, find and correct the cause, then recheck the system.
- If the input test proves OK, go to step 19.

Door Multiplex Control Unit

19. Turn the ignition switch OFF.
20. Remove the power window master switch.




21. Disconnect the 23P connector from the power window master switch.
22. Inspect the connector and socket terminals to be sure they are all making good contact.
- If the terminals are bent, loose or corroded, repair them as necessary, and recheck the system.
- If the terminals look OK, go to step 23.




23. With the connector still disconnected, make these input tests at the connector.
- If the test indicates a problem, find and correct the cause, then recheck the system.
- If the input tests prove OK, go to step 24.




24. Reconnect the connector to the door multiplex control unit. Turn the ignition switch ON (II) and make these input tests at the connectors.
- If any test indicates a problem, find and correct the cause, then recheck the system.
- If all the input tests prove OK, go to step 25.

25. If all the input tests prove OK, and no DTCs were found during MICS troubleshooting (B-CAN System Diagnostic Test Mode A), go to the B-CAN system input and output index. Description and Operation If multiple failures are found on more than one control unit, replace the driver's under-dash fuse/relay box (includes the MICU). If input failures are related to a particular control unit, replace that control unit.
pro multis · About Operation CHARM