Operation CHARM: Car repair manuals for everyone.
Home >> Honda >> 2008 >> CR-V 2WD L4-2.4L >> Repair and Diagnosis >> Powertrain Management >> Sensors and Switches - Powertrain Management >> Sensors and Switches - Computers and Control Systems >> Crankshaft Position Sensor >> Service and Repair >> CKP Pulse Plate Replacement

CKP Pulse Plate Replacement




CKP Pulse Plate Replacement

1. Remove the front wheels.
2. Remove the splash shield.
3. Remove the drive belt.
4. Remove the cylinder head cover.
5. Set the No. 1 piston at top dead center (TDC). The punch mark on the variable valve timing control (VTC) actuator and the punch mark on the exhaust camshaft sprocket should be at the top. Align the TDC marks on the VTC actuator and exhaust camshaft sprocket.
6. Disconnect the crankshaft position (CKP) sensor connector and VTC oil control solenoid valve connector.
7. Remove the VTC oil control solenoid valve.
8. Remove the crankshaft pulley.
9. Support the engine with a jack and wood block under the oil pan.
10. Remove the upper torque rod.
11. Remove the ground cable, then remove the side engine mount bracket.
12. Remove the side engine mount bracket mounting bolts.
13. Remove the cam chain case and side engine mount bracket.
14. Remove the CKP pulse plate.





15. Install the CKP pulse plate.
16. Check the chain case oil seal for damage. If the oil seal is damaged, replace the chain case oil seal.
17. Remove all of the old liquid gasket from the chain case mating surfaces, bolts, and bolt holes.
18. Clean and dry the chain case mating surfaces.
19. Apply liquid gasket, P/N 08717-0004, 08718-0001, 08718-0003, or 08718-0009, evenly to the engine block mating surface of the chain case. Install the component within 5 minutes of applying the liquid gasket.

NOTE:
- If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.
- If too much time has passed after applying the liquid gasket, remove the old liquid gasket and residue, then reapply new liquid gasket.

20. Apply liquid gasket to the engine block upper surface contact areas on the chain case and lower block upper surface contact areas on the chain case.
21. Apply liquid gasket, P/N 08717-0004, 08718-0001, 08718-0003, or 08718-0009, evenly to the oil pan mating surface of the chain case. Install the component within 5 minutes of applying the liquid gasket.

NOTE:
- If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.
- If too much time has passed after applying the liquid gasket, remove the old liquid gasket and residue, then reapply new liquid gasket.

22. Install the new O-ring, side engine mount bracket, and mounting bolts on the chain case. Set the edge of the chain case to the edge of the oil pan, then install the chain case on the engine block. Wipe off the excess liquid gasket on the oil pan and chain case mating area.

NOTE:
- When installing the chain case, do not slide the bottom surface onto the oil pan mounting surface.
- Wait at least 30 minutes to allow liquid gasket to cure before filling the engine with oil.
- Do not run the engine for at least 3 hours after installing the chain case.

23. Tighten the side engine mount bracket mounting bolts.
24. Install the side engine mount bracket, then loosely tighten the new bolt and nut, and loosely tighten the bolt. Install the ground cable.
25. Remove the air cleaner housing assembly.
26. Loosen the transmission mounting bolt and nuts.
27. Raise the lift to full height.
28. Loosen the lower torque rod mounting bolt.
29. Lower the vehicle on the lift.
30. Tighten the side engine mount mounting bolts and nut.
31. Tighten the transmission mounting bolt and nuts.
32. Raise the lift to full height.
33. Tighten the lower torque rod mounting bolt.
34. Lower the vehicle on the lift.
35. Install the air cleaner housing assembly.
36. Install the upper torque rod, then tighten the new upper torque rod mounting bolts in the numbered sequence shown.
37. Install the VTC oil control solenoid valve.
38. Connect the CKP sensor connector and VTC oil control solenoid valve connector.
39. Install the crankshaft pulley.
40. Install the cylinder head cover.
41. Install the drive belt.
42. Do the CKP pattern clear/CKP learn procedure below.

Crank (CKP) Pattern Clear/Crank (CKP) Pattern Learn

Clear/Learn Procedure (With the HDS)




1. Connect the HDS to the data link connector (DLC) (A) located under the driver's side of the dashboard.
2. Turn the ignition switch ON (II).
3. Make sure the HDS communicates with the PCM and other vehicle systems. If it doesn't, go to the DLC circuit troubleshooting. Testing and Inspection
4. Select CRANK PATTERN in the ADJUSTMENT MENU with the HDS.
5. Select CRANK PATTERN LEARNING with the HDS, and follow the screen prompts.
6. The CKP pattern learn procedure is complete.

Learn Procedure (Without the HDS)
1. Start the engine. Hold the engine speed at 3,000 rpm without load (in Park or neutral) until the radiator fan comes on.
2. Test-drive the vehicle on a level road: Decelerate (with the throttle fully closed) from an engine speed of 2,500 rpm down to 1,000 rpm with the transmission in 2 position.
3. Repeat step 2 several times.
4. Turn the ignition switch OFF.
5. Turn the ignition switch ON (II), and wait 30 seconds. The CKP pattern learn procedure is complete.
pro multis · About Operation CHARM